Which Brake Controller Wiring Harness Fits a 1997 Ford F-150

Question

Question:

Will this adapter work with my 97 F-150? I see an open plug in under the dash that appears to be this shape.

asked by: Jim

0

Expert Reply:

If your 1997 Ford F-150 came with a factory 7-Way or 4-Way then you can use the brake controller wiring adapter # 3035-P for Tekonsha brake controllers, or # HM47715 for a Hopkins brake controller. I have included a link to the installation details for the Hopkins and Tekonsha harnesses for you to view.

expert reply by: Michael H

0

Answer 1

There are a few differences between the two controllers. The Voyager has been around for a looooooooong time. It uses an internal pendulum to determine how quickly the tow vehicle is braking. In order to operate correctly, this level of the pendulum…

view full answer...

Answer 2

You should be fine as most people do not have trailer wheels and tires balanced, but if you are having a shop mount the tires, and you want to have them balanced, it probably would not cost much more to have the setup balanced as well. One reason…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 12

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Which Brake Controller Wiring Harness Fits a 1997 Ford F-150

Products Referenced in This Question

Featured Help Information

Instructions

Continue Researching