Lug Nut Torque For Aluminum Hi-Spec Series 6 Trailer Wheel # AM22697

Question

Question:

What is the torque for the nuts

asked by: George K

1

Helpful Expert Reply:

The Aluminum Hi-Spec Series 6 Trailer Wheel # AM22697 is an aluminum 16 inch diameter trailer wheel so the lug nut torque required for it is 90-100 ft lbs.

expert reply by: Jameson C

1

Answer 1

On trailer brakes the small shoe points towards the front of the trailer, and the larger shoe points towards the rear. This allows the trailer brakes to apply correctly when the magnet for electric brakes is activated, or the wheel cylinder is…

view full answer...

Answer 2

It sounds like you have shorted the brake output circuit of the new trailer 7-way with the 12 volt power circuit and that is causing the trailer brakes to stay on all the time. The best recommendation I have would be to go over the install looking…

view full answer...

Answer 3

You should be turning the star wheel up to tighten your electric brakes, as you mentioned. This could mean they are improperly mounted and I recommend taking a look at your brake assemblies to see how they were put on. You will need to disassemble…

view full answer...

Answer 4

You are correct, the shorter shoe should be forward on electric brake assemblies like the 12 inch Electric Brake Assembly, #23-105, that your selected. In my experience, the shorter shoe is always the shoe that is pressed against the drum first,…

view full answer...

Answer 5

I have attached a chart that gives the torque specs for trailer lugs based on stud size, wheel size, and wheel material. For your Aluminum HWT Mod 15 Inch Trailer Wheel, #AM22646, and 1/2 inch stud size, the proper torque is 90 to 100 ft lbs.…

view full answer...

Answer 6

A bearing race or cone should fit tightly enough in the hub that it needs to be driven out of the hub with a punch from the back side. If the race is spinning in the hub, either the wrong race was used or the hub bore has been damaged in some way.…

view full answer...

Answer 7

Yes, the TorkLift Lock and Load SideKick #TLA7901 that you referenced will fit a Honda 2200 generator like you mentioned. We had the chance to fit one on this carrier and it worked well. See attached picture. It's also in the review video…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Lug Nut Torque For Aluminum Hi-Spec Series 6 Trailer Wheel # AM22697

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching