How Long is the Valterra Bladex Waste Valve for RV Black Water Part T50 From Each Fitting

Question

Question:

Can you tell me the measurement front to back ie from the LUG side fitting to the Hub side fitting . And how deep is the HUB ?

asked by: Robert G

0

Expert Reply:

The Valterra Bladex Waste Valve for RV Black Water part # T50 measures 4-1/8" from the end of the lug fitting to the end of the hub fitting. The hub fitting is then 1-1/2" deep.

expert reply by: Conner L

0

Answer 1

The end of the Valterra Waste Valve for RV Black Water Tank #T50B that has the lugs has a 3" diameter but the other side with the threads is actually designed to fit over a 3" diameter threaded sewage pipe which is why it measures…

view full answer...

Answer 2

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 3

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 4

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 5

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 6

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 7

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 8

Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake controller…

view full answer...

Answer 9

It is really not a great idea to drive with a trailer cover like the part #052963735635 installed on a trailer. The only way I could safely recommend you do so is if you were to keep the speeds under 25 miles per hour and you weren't on a public…

view full answer...

Answer 10

Brake magnets are made to fit their specific brake assemblies. They are not made to be interchangeable between brake sizes or weight capacities. Some manufacturers do use different color magnet wires that correspond to the capacity. We know that…

view full answer...

Answer 11

Actually on brake magnets for trailers either wire can be used as the power or the ground so the colors don't really mean anything. Most likely the magnet manufacturer just put what ever color was most convenient on your trailer.

view full answer...

Answer 12

Most likely the new axle has self-adjusting brakes which when new are known for feeling pretty weak. The good news is that you can keep applying them over and over while the trailer is traveling and they will tighten and get more sensitive feeling.

view full answer...

How Long is the Valterra Bladex Waste Valve for RV Black Water Part T50 From Each Fitting

Product Page this Question was Asked From

Continue Researching