Recommended ST205/75R14 Tire and Wheel for Boat Trailer

Question

Question:

Any recommendation for wheels/tires for a single axle galvanized trailer hauling an 18foot bowrider boat? Currently running 205/75 r14 load range C. Pic is of the boat on a steel trailer that Im replacing with a galvanized one.

asked by: Andrew

0

Expert Reply:

For your Larson Bowrider Boat Trailer I highly strongly the Castle Rock ST205/75R14 Radial Tire w/ 14" Condor Aluminum Wheel - 5 on 4-1/2 - LR C - Gunmetal # LH84VR. This radial ply tire features a double steel belt construction with double polyester cords that allow for a longer lifespan and automotive-grade tread to improve traction on the road, especially during wet weather. The 14-inch aluminum wheel is completely resistant to rust and corrosion, so you don't have to worry about it breaking down as your launches start to add up.

The tire features a maximum load of 1,760 pounds at 50 psi and an excellent speed rating of 75 mph (most trailer tires are rated for 65 mph).

I have attached a short video review that you can check out as well.

expert reply by: Chris R

0

click to enlarge

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 3

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 6

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 7

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

You will need to measure the diameter of the spindles where the seal and bearings ride. Check out the picture I attached that shows where this is. You will need an exact measurement so either a digital or dial caliper will be needed. To pick out the…

view full answer...

Recommended ST205/75R14 Tire and Wheel for Boat Trailer

Product Page this Question was Asked From

Continue Researching