Thickness of Buyers Products Lunette Ring # 337BDB125015W

Question

Question:

What is the ring thickness and the width of the ring. I know inner opening is 2 1/2” across. But need to know what width is on one side of the ring. The one I have now is 1 1/4” thick. Needing it to be 1 1/2” across like product #63023 that you sale.

asked by: Ron P

1

Helpful Expert Reply:

I went out to our warehouse and measured the thickness/width on the Buyers Products Lunette Ring # 337BDB125015W to be right at 1-1/2 inches. The overall outer width of the ring is 5-1/2 inches. I have attached an image to assist.

expert reply by: Chris R

1

click to enlarge

Answer 1

I called my contact at Buyers Products and they informed me that the Buyers Products Welded Mount Lunette Ring part #337BDB125015W is 5-1/2" x 5-1/2" and the mounting holes are all 4-1/2" apart top to bottom and side to side. I have…

view full answer...

Answer 2

The thickness of the plate that the lunette ring of the #337BDB125015W mounts to is 3/4 inches.

view full answer...

Answer 3

The only way to use sway control on a trailer that uses a pintle hitch set up is to use the Tuson electronic sway control system #335TSC-1000. The trailer has to have electric brakes to use this though. When it senses sway it will apply the trailer…

view full answer...

Answer 4

The Buyers Products Drawbar Wear Gauge #3373013872 can be used to measure your pintle hook for wear given that it is not thicker than 1-9/16". You will want to use the gauge closest to the original size of the pintle hook, and if you get down to…

view full answer...

Answer 5

Due to the heavy duty nature of the lunette style pintle setups there isn't a bushing available for the rings. The sway you are experiencing is most likely due to improper trailer loading. If you move as much of the weight of your cargo forward…

view full answer...

Answer 6

The larger tire size you want to go with will increase your overall tire diameter by 1-1/2 inches. That means that you would have 3/4 of an inch less trailer fender clearance. You would need to check out the trailer to determine if you have the…

view full answer...

Answer 7

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 8

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 11

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 12

It's totally normal for a bit of movement between any fifth wheel hitch and the base rails. The feet on the hitch are typically a bit smaller than the slots they slide into for mounting otherwise you'd have a hard time getting your hitch in…

view full answer...