Owner's Manual for Progressive Dynamics Inteli-Power RV Converter and Smart Battery Charger

Question

Question:

Model PD9260C Rec. Veh. Converter/Charger. How old is this model. Where can I get an owners manual? Thanks

asked by: Christopher P

0

Expert Reply:

I have attached a link for you of the owner's manual of the Progressive Dynamics Inteli-Power RV Converter and Smart Battery Charger - 12V - 60 Amps # PD9260C; I have also added a link to a video review of this converter for you to take a look at.

There isn't a specific age I can offer for you for this converter.

expert reply by: Kyle S

0

Answer 1

For a similar 60 amp converter that can charge a lithium battery you'd want the part #PD9160ALV but the part #PD9260C can only charge lead acid batteries.

view full answer...

Answer 2

I do have a simple wiring diagram for the Progressive Dynamics Inteli-Power RV Converter and Smart Battery Charger - 12V - 45 Amps #PD9245C. Basically you just need to run the power wire from the converter directly to the DC distribution panel and…

view full answer...

Answer 3

If you check out the diagram I attached you will see how the steps should get wired up. What I would first do is verify that you have voltage in all of the right places on your steps to determine if the module needs to be replaced with the #LC301702.…

view full answer...

Answer 4

The Replacement Control Module for Lippert Electric Coach Step #LC301702 is the correct fit for your Lippert Coach step. The long green wire with the ring terminal is your ground and will be attached bare metal to metal on our coach frame. The short…

view full answer...

Answer 5

The Replacement Control Module for Lippert Electric Coach Step #LC301702 has the purple wire that connects to the door light switch. The other end of the switch #LC301694 connects to the Replacement Wiring Harness for Lippert Electric Coach Step…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 11

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...