Dimensions of Door Strap Hinge # 2510 for International Trailer

Question

Question:

trailer door hinges for a 6 by 10. International trailer double back doors. lock on both sides of the trailer Thanks

asked by: Tim F

0

Expert Reply:

I have provided photos showing the dimensions of the # 2512 hinge, which you can compare to your existing hinge. This should give you a good idea if the # 2512 hinge will work for you, as I do not have any information about the OEM hinges on your International utility trailer.

expert reply by: Mike L

0

click to enlarge

Answer 1

I am assuming the boat is on a trailer when stored in the boat house which will make things a lot easier. So basically what you could do is use a winch that can pull/lower the trailer and boat up and down the ramp. To load the boat on the trailer you…

view full answer...

Answer 2

You will have to determine where the sag is coming from. Are the hinges worn out? If so, you would need to replace them. We have strap hinges like the part #2512 which are commonly what is found on barn style trailer doors.

view full answer...

Answer 3

You can purchase the Strap Hinge for Enclosed Cargo Trailer Doors 180 right here at etrailer.com. All you need to do is click this product number: #2512 This will bring you to the product page where you can enter the quantity you need and you'll…

view full answer...

Answer 4

I have reached out to my contact at Polar before asking about the weight rating of their straps, like part #2512, and I have been told that they don't really have a weight rating. There are so many different variables into the equation that it is…

view full answer...

Answer 5

Since heat rises I would at the very least put a set of the Trailer Vents #HMAV2-AVT2 near the top of the trailer to get the hottest air of the trailer out. What you could do for maximum air flow in your trailer is have a set facing forward in the…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Dimensions of Door Strap Hinge # 2510 for International Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching