How to Select the Correct Grease Seals for a 2008 Interstate LoadRunner 5x10 Cargo trailer
Question:
Hi guys - I have a 2008 Interstate LoadRunner 5x10foot Cargo trailer that I would like to pre-purchase grease seals for before repacking the bearings. 1 Interstate does not have the part numbers with reference to the VIN 2 I do not want to disassemble the hub yet to get any part numbers because it is cold and snowy outside - I will only have one shot at this 3 It has a 3500 lb axle with 5 on 4 1/2inch hubs and 15inch tires. Is there any way to know what grease seals to purchase? Thank you for your time and assistance.
asked by: Brian
Expert Reply:
It is difficult to determine the correct grease seal for your trailer without either information from the trailer manufacturer or removing the trailer hub and getting part numbers or measuring. The actual seal part number form the rubber portion of the seal would be the best way to determine the correct seal, and the next best way would be to use the bearing part numbers to select the correct seal for the hub and spindle.
For the 3500 lb axle with 5 on 4 1/2 inch bolt pattern hubs, there are 3 different grease seals that are commonly used. The most common is the double lip grease seal 10-19, # RG06-050, next there is the double lip grease seal 10-60, # RG06-020, and finally the double lip grease seal 12192TB, # RG06-010.
The inner and outer diameter of all of these seals is different so we would need to match them to the bearings that they work with or take a measurement to be sure we select the correct seals.
There is one possibility for measuring without removing the hub as long as your trailer does not have brakes on the axle. The brake backing plate would not allow for this measurement, and if you have a brake mounting flange on the axle it could make the task more difficult.
You would need to safely raise one of the trailer wheels, remove the grease cap, and loosen the spindle nut most of the way. There is no need to remove the wheel and tire but it may make the process a bit easier. Then lie on the ground so you can see the back side of the hub where the grease seal rides on the spindle, see photo. You should be able to push the hub out enough now so that you can get a dial caliper in there, or use a measuring caliper, to get the correct measurement for the seal bearing surface on the spindle.
If you do this, you can select the correct seal from the inside dimensions (I.D.) on the product pages I linked for you.
The Bearing Buddy grease seal that you selected, # BB60005, would not be the correct replacement for your axle.
Products Referenced in This Question
Double Lip Grease Seals (pair)
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 1.249 Inch I.D.
- 1.983 Inch O.D.
- TruRyde
more information >
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 1.500 Inch I.D.
- 1.987 Inch O.D
- TruRyde
more information >
Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 2
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 1.719 Inch I.D.
- 2.565 Inch O.D.
- etrailer
more information >
Product Page this Question was Asked From
Spindle Grease Seal Set for L44649 Inner Bearing and 1.980 Bearing Buddy
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 1.375 Inch I.D.
- 1.98 Inch O.D.
- Bearing Buddy
more information >
Continue Researching
- Shop: Kenda Loadstar 5.30-12 Bias Trailer Tire with 12" White Wheel - 5 on 4-1/2 - Load Range C
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: etrailer Class III Trailer Hitch Installation - 2023 Kia Telluride
- Shop: Trailer Hitch
- Shop: Curt Easy Mount Bracket for 4- or 5-Way Flat and 6- or 7-Way Trailer Connectors - 2-1/2" Hitch
- Shop: Curt Easy Mount Bracket for 4- or 5-Way Flat and 6- or 7-Way Trailer Connectors - 2" Hitch
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Kenda 5.30-12 Bias Trailer Tire with 12" Galvanized Wheel - 5 on 4-1/2 - Load Range C
- Search Results: 7 way 4 way connector
- Video: Bearing Repacking and Grease Seals Installation
- Video: Hopkins 7-Way RV to 4-Way Flat Trailer Connector Adapter Review HM47365
- Video: Review of Hopkins Wiring - Wiring Adapters - HM47365
- Q&A: Does Grease Seal Thickness Matter More than Inner and Outer Diameter
- Q&A: Single or Double Lip Seals for a Trailer with 12192TB Transcom Seals and Using Bearing Buddies
- Q&A: Recommended Replacement Grease Seal for 2014 Shorelander Boat Trailer
- Q&A: Replacement Trailer Bearings for Shoreland’r Trailer with #84 Spindle
- Q&A: How to Determine Correct Replacement Grease Seal
- Shop: Double Lip Grease Seals (pair)
- Shop: Double Lip Grease Seal - ID 1.249" / OD 1.983" - Qty 1
- Q&A: What is the Speed Rating of Trailer Tire and Wheel Combo # AM30820
- Q&A: What Are The Torque Specs And PSI Rating For Kenda 5.30-12 Galvanized?
- Article: Trailer Hitch Receiver Sizes
- Video: Timbren Axle-Less Trailer Suspension System Installation