Front Mount Trailer Hitch Receiver for a 2Wheel Drive 1999 Ford Expedition

Question

Question:

I have been looking for a hitch for this car, but there are no drilled holes any where in the frame members to use. I dont have the tow hooks to remove to provide holes so how do you attach the hitch??

asked by: Dennis W

0

Expert Reply:

The front mount trailer hitch # 65025 does fit the 1999 2 wheel drive Ford Expedition. There should be holes on the inboard side of each frame rail. I have included a link to the installation details that shows where the hitch installs on the vehicle.

expert reply by: Michael H

0

Answer 1

If you wish to retain the front tow hooks on your 1998 Ford F-150 then you are going to want to use the Curt Front Mount Trailer Hitch Receiver part #31049, not the Draw-Tite Front Mount Trailer Hitch Receiver part #65025. The reason for this is that…

view full answer...

Answer 2

According to my contact in the Tech Services department at Curt Manufacturing, their #31049 will fit a 1998 Ford F150 2WD model as long as it has factory tow hooks mounted to the underside of the frame members. Draw-Tite has the #65025 listed as a…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 11

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Answer 12

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Front Mount Trailer Hitch Receiver for a 2Wheel Drive 1999 Ford Expedition

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching