Saw Recommendation for Cutting Down Anderson Levelers # AM3604

Question

Question:

Instructions say to use a meter saw to cut the levelers, but what kind of blade would you use?

asked by: Bob P

0

Expert Reply:

It won't be hard to cut the Andersen Camper Wheel Chock and Leveler # AM3604 with any type of power saw as it is made of plastic. If you have access to a miter saw that would be an easy and safe option that I would recommend highly but it's going to come down to what you feel the most comfortable with and what you have access to.

expert reply by: Jameson C

0

Answer 1

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 2

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 3

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 4

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 5

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 6

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hi James, To my knowledge the Reese Goosebox is the only replacement option that won't void the frame warranty. That being said, the frame warranty is typically only a year so you really aren't losing much voiding it, especially if you've…

view full answer...

Answer 9

The Head Unit and R16 Roller Adapter #C16515 is more of an entry level fifth wheel head designed for a lower price point, whereas the A16 part #C16520 is a bit nicer with it's 2 piece jaw system that will provide better king pin contact which…

view full answer...

Answer 10

Hi Joe, I assume you are referencing an Equal-i-zer weight distribution since you have shank #EQ90-02-4700. I went ahead and read the owners manual for their systems and there is noting regarding adjusting the angle of the hitch ball. The hitch head…

view full answer...

Answer 11

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 12

Thank you for the photo of your 2016 Ram 3500's bed rail which sits 59-inches above ground. You are correct that the recommended minimum clearance between a bed rail and the underside of the trailer's overhang is 5 to 6-inches, as shown in…

view full answer...

Saw Recommendation for Cutting Down Anderson Levelers # AM3604

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching