Should Hole be Drilled in Axle for Leaf Spring with Center Bolt to Fit Properly

Question

Question:

How should I mount my axle on leaf springs when there is a bolt head right in the center of the springs? Should I drill a holes in the axle so it rests on the springs or balance it on top of the bolt?

asked by: Greg

0

Expert Reply:

Great question!

When installing leaf springs that have a stack with a bolt in the middle, like the 3,500 lbs Axle # e54SR, you will actually be installing them using a Spring Seat # TRSS238 which welds on to your trailer axle and gives you the support needed as well as a hole in the middle where that center bolt goes through.

expert reply by: Jon G

0

Answer 1

I may have a solution for you, however the Inno Truck Bed Cargo Rack #INRT101-79 referenced in your question is designed specifically for certain model truck beds, so it might not be the best fit for your utility trailer. For your trailer, I…

view full answer...

Answer 2

Yes, the Yakima HangOut 3 #Y02638, is a confirmed fit the 2014 Toyota Highlander. I have included a video review of this bike rack for you to check out. If you will be carrying womens, childrens, or alternative frame bikes I recommend using the Tube…

view full answer...

Answer 3

I checked with Yakima and the Hangout part #Y02637 that you referenced is a confirmed fit and will work well. This will carry two mountain bikes easily, but sometimes Trek has alternative shaped frames so you may need to use an adapter bar like part…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Should Hole be Drilled in Axle for Leaf Spring with Center Bolt to Fit Properly

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching