Install Port Location for Tekonsha P3 Brake Controller in 2018 Tiffin Allegro Open Road 36LA

Question

Question:

Can you tell me where the brake controller plug on my 2018 Tiffin Allegro Open Road 36LA is located and where is the best place to mount the Tekonsha P3 Brake Controller. Thankyou

asked by: Paul

0

Expert Reply:

The install harness needed to install the prodigy P3 part # 90195 in your 2018 Tiffin Allegro Open Road 36LA is the part # 3035-P which is located under the dash of your vehicle. I attached a picture that shows where you'll find the port on your motorhome for you to check out as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I am not entirely sure what process you took so I'll give you some other things to try, or maybe a different way to test the Prodigy P3 #90195. First, sever the blue wire a couple inches from the back of your controller. Then use a circuit tester…

view full answer...

Answer 2

To see a couple diagrams that show how the 6-way to 7-way adapter part #47435 is wired up check out the pictures I attached. The 6-way of this adapter has the center pin as the 12 volt circuit. That is the usual circuit that gets moved around on…

view full answer...

Answer 3

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 4

I may have another option for you, but unfortunately there is not a way to carry two 54lb electric bikes on the Malone MicroSport Trailer for 2 Fat Bikes and 2 Kayaks #MPG461KB you were looking at as the included bike racks have a 33lb weight rating…

view full answer...

Answer 5

We carry a very handy 2 inch ball mount for this exact application. The part is #D210. The ball mount slides and pins into your hitch and the top receiver will accept 2 inch bike racks and hold them above the ball. The Ball Mount has a 500 lb tongue…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

Hello Curtis. You can absolutely use an RV mount tow bar with your 2006 Ford E350 Van. For example, the Blue Ox Avail Non-Binding Tow Bar #BX7420 is compatible with any 2" hitch receiver. This could be on a motorhome, van or pickup truck. As…

view full answer...

Answer 12

You do have the option to utilize the air brakes on your 2023 Freightliner Cascadia to control electric trailer brakes using the Hayes Air Actuated Trailer Brake Controller, part #HA100400C. However, we mostly recommend just using an electric brake…

view full answer...