Where to Connect Curt Stabilizer Strap When Using with a Camper

Question

Question:

How do you connect it to back of camper? There does not seem to be any places to hook to.

asked by: Jeffery C

0

Expert Reply:

You can actually attach the Curt Stabilier Strap # 18050 to the safety chain loops on your Curt trailer hitch. I reached out to Curt and they confirmed that this is how you want to use the strap when a hatch is not readily available (like on some passenger vehicles).

expert reply by: Jon G

0

Answer 1

The Curt Trailer Hitch Support Strap part #18050 is required to be used with all Curt Class I hitch receivers for all non-towing purposes. As you are using the hitch to secure a bike rack, you will need to use this strap to further support the load…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Hey Dave, so the best option for carrying your carbon frame bike and e-bike is the Swagman Escapee part #S39SR with the ramp #S59SR . It has the capacity for carrying an e-bike, is rated for travel trailer use, only touches the bikes by the tires…

view full answer...

Answer 4

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 5

Yes, you can install a Curt Trailer Hitch Receiver #C11433 on your 2019 Chevrolet Spark. This receiver is capable of supporting up to 200lbs of tongue weight. With each of the Lectric 3.0 e-bikes weighing roughly 60lbs without the battery you will…

view full answer...

Answer 6

I have a solution for you. Here at Etrailer, we strongly discourage using wheel-mounted bike racks like the Kuat NV 2.0 #NV22B for bikes with fenders. Mounting wheels with fenders can cause the fenders to crack or become damaged, especially with the…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

As long as the flat tow wiring is wired in before the 4-Way #C93ZV and you connect the power for the converter directly to the battery it will work. I have seen several use Magnetic Lights #TL21RK which they will wire in on the main harness to have…

view full answer...

Answer 9

The RockyMounts MonoRail bike rack you'd looked at, part #RKY10004 is a great bike rack, but it wouldn't work well with bikes that have fenders like your Aventon Aventure Fat tire ebikes. The front fender would prevent the bike retaining hook…

view full answer...

Answer 10

In order to use a hitch-mounted bike rack like the Swagman Original #S64152-2 that you were looking at while towing a vehicle, you will just need to add the Roadmaster Dual Hitch Receiver Adapter #RM-077-4. This adapter will slide into the 2 inch…

view full answer...

Answer 11

Only certain bike racks are rated for use at the back of an RV or trailer but the Hollywood Racks #HR1400Z bike rack is not one of them. Generally, any rack that can fold or tilt, with few exceptions, won't be rated for this applications. The…

view full answer...

Answer 12

At the rear of a trailer or RV the ride quality is very rough when compared to the ride quality at the rear of a passenger vehicle. Reason being the suspension isn't as sophisticated and there is a longer distance between the rear axle and the…

view full answer...

Where to Connect Curt Stabilizer Strap When Using with a Camper

Product Page this Question was Asked From

Continue Researching