Bike Rack Solution for 2019 Hyundai Kona EV

Question

Question:

Unfortunately the previous answers regarding this subject have no dates. They talk about a 2018 Kona EV, however there is no 2018 Kona EV at least here in the USA So i am looking for a hitch for a 2019 Hyundai Kona EV for the purposes of a 2-bike rack. Will the DT52GR Drawtite fit?

asked by: Tony R

0

Expert Reply:

The EV version of the 2019 Hyundai Kona is the fully electric version which we have the Draw-Tite Max-Fram Trailer Hitch # DT52GR. This is a class 3 hitch with a 2" receiver opening. This will give you a wide array of bike racks from which to choose.

expert reply by: Jameson C

0

John P.

5/24/2020

Doesn't Yakima not recommend this rack for cars that have a rear spoiler like the Kona EV

Reply

Chris R.

5/27/2020

The Yakima FullBack is actually designed to fit around most factory spoilers. To be certain it's okay to use on yours, simply go through our vehicle fit guide to see if the FullBack Rack shows up as a good fit. If you let me know what vehicle you have I will be happy to verify this for you as well.

Reply

Answer 1

I checked with Draw-Tite and they do show the Draw-Tite Max-Frame Trailer Hitch Receiver part #DT52GR as a fit for a 2023 Hyundai Kona EV. This trailer hitch features a bolt-on install so there's no drilling required. It has a class III rating…

view full answer...

Answer 2

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Bike Rack Solution for 2019 Hyundai Kona EV

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching