Meaning of Blinking Light on Atwood Carbon Monoxide/Propane Gas Detector AT31012

Question

Question:

Is it normal for the Atwood RV Carbon Monoxide and Propane Gas Detector light below the propane to blink? If not how do I correct it? Atwood RV Carbon Monoxide and Propane Gas Detector - 12 Volt - Black Item # AT31012.

asked by: Donna W

0

Expert Reply:

My contact at Atwood advised that the light under the "Propane" label blinking red indicates the propane detector is disabled. The blinking indicates that the sensor is worn out and the unit should be replaced with # AT36681.

For reference the complete instructions, including the procedure for testing this unit, will be sent to you in a separate email.

expert reply by: Adam R

0

Answer 1

The red blinking light on the Atwood RV Carbon Monoxide and Propane Gas Detector part #AT36681 under the propane heading means that the propane sensor is disabled or faulty. I recommend doing a hard reset of the unit but if that does not work then…

view full answer...

Answer 2

We've seen this issue before on your Atwood RV Carbon Monoxide and Propane Gas Detector #AT36681 and the beeping every 40 seconds indicates "a fault has been detected that compromises some detector function." What you need…

view full answer...

Answer 3

On your Atwood RV Carbon Monoxide and Propane Gas Detector #AT36681 there is a circle Reset/Test button on the top right hand corner of the unit. Simply pressing this button should reset the detector and silence any alarms assuming there…

view full answer...

Answer 4

The instructions state the rest/test button of the Atwood RV Carbon Monoxide and Propane Gas Detector - 12 Volt - White #AT36681 is the button on the top right, and you need to press that in and hold it down. If the rest does not work and the red…

view full answer...

Answer 5

The lifespan of Atwood carbon monoxide and LP sensors like the part #AT36681 that you referenced is 7 years so if you are having alarms go off at 2-1/2 years I'd recommend taking the alarms seriously. You can also make sure the batteries that it…

view full answer...

Answer 6

You can use the RV Propane Gas Detector #RS64FR to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 7

Those tabs are the answer. They can be pretty tight so you may need a small screwdriver to push them in. If you can get one side or end started then it will be easy to pull the cover off the Atwood RV Carbon Monoxide and Propane Gas Detector…

view full answer...

Answer 8

It sounds like your Atwood RV Carbon Monoxide and Propane Gas Detector part #AT36681 is hooked up properly and is getting power. The code you hear is like you said a fault code in this case because of the audible tone. I recommend replacing it. The…

view full answer...

Answer 9

If you're getting a fault with your Atwood RV Carbon Monoxide and Propane Gas Detector #AT36681 then I would first ensure that there's no presence of propane and then would cut power to the detector for a few minutes to let it fully power…

view full answer...

Answer 10

In order to help prevent leaking between the grommet and tank on the Replacement Rubber Grommet for RV Black Water Tanks part #F02-2106 it would be wise to use a sealant like part #LT37467 between the two surfaces. I am not sure if this is a…

view full answer...

Answer 11

Let's get you a new detector so you are safe, see the linked items below: **RV Propane Gas and Carbon Monoxide Detector - 12 Volt - 2 Wire - White #RS34FR. The part you are referencing is no longer available. The alarm itself is 4-1/4" long…

view full answer...

Answer 12

B&W re-designed the RVK3400 hitch with a little bit different styling and changed the part number to the RVK3405. Our part #BWRVK3400 is the RVK3405 but we just didn't change our part number.

view full answer...

Meaning of Blinking Light on Atwood Carbon Monoxide/Propane Gas Detector AT31012

Continue Researching