Vertical Distance Between Hitch Pin Holes of Curt Dual Adapter part # D-192

Question

Question:

I see the extension between the center holes is 8inch but you dont provide the rise or between the center holes of upper and lower recievers ? Can you tell me please ?

asked by: Scott C

0

Expert Reply:

The vertical distance between the upper and lower hitch pin holes on the Curt Dual Adapter part # D-192 is 5-3/4 inches.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The setup you sent in a picture of is going to have a hitch tongue weight setup reduced by 50 percent. It's the added length added to the hitch and the increased movement that puts leverage and stress on the hitch which is why the capacity is…

view full answer...

Answer 2

Hitch extenders and similar adapters cut the capacity of the hitch they are installed on in half so I can't recommend any product (if there was one available), that would allow you more clearance so that your wheel chair carrier would clear the…

view full answer...

Answer 3

The Curt Dual 2 inch Receiver Tube Adapter, with 8 inch Extension, item #D-192, is not for use with any type of trailer. The dual receivers that we carry are only rated for use while towing vehicles with 4 wheels down. You could possibly use the Curt…

view full answer...

Answer 4

The best solution to raise your Curt hitch-mounted cargo carrier further above the ground is with an adapter like the Curt #D-192. This provides you with a top 2 inch receiver that sits 3-1/4 inches above the hitch on your vehicle. As you referenced…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 8

Since the issue appears to be on the vehicle side for your 2017 Toyota Tacoma, I recommend first checking the connector itself. Look to see if there is any dirt or corrosion built up inside the connector that may preventing a solid connection with…

view full answer...

Answer 9

The first thing you'll need to flat tow your 2015 Chevy Malibu LS is a base plate kit like the Roadmaster part #RM-523178-5 that is a confirmed fit. In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting,…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

There is a suggested and common method for 6 function trailer wiring. You will have the following functions: Right Turn, Left Turn, Ground, Tail/marker, Brake, Battery. I have included a help article on trailer wiring that includes a diagram and…

view full answer...

Answer 12

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Vertical Distance Between Hitch Pin Holes of Curt Dual Adapter part # D-192

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching