Follow Leg Repair Kit for 2010 Keystone Laredo 298BH Venture Landing Gear

Question

Question:

Wondering if there is a repair kit for the landing gear on my camper. It would be the follow side and the part # I got from the dealer is 120238 and it is a Venture. They are telling me I need to replace the entire leg which seems strange to me.

asked by: Aaron G

0

Expert Reply:

The Lippert Components Venture Follow Leg Repair Kit for 5th Wheel RV Landing Gear # LC146060 is what you need for your follow leg. I've attached a photo to assist.

expert reply by: Jason S

0

click to enlarge

Answer 1

Most of the Keystone trailers came with Lippert landing gear so for a replacement follow leg repair kit you'd want the part #LC146060. Double check to make sure you have Lippert, Venture, or Stromberg brand landing gear. If so, this would be the…

view full answer...

Answer 2

The lead jack is typically the one with the hand crank and motor attached to it. For your Venture VMC900R landing gear setup you will want to go with Lead Jack Repair Kit for Stromberg Carlson Landing Gear #LG-146059.

view full answer...

Answer 3

I linked the schematic diagram for Lead Jack Repair Kit #LG-146059 taken from the written instructions. The complete instructions will be sent to you in a separate link. The follow leg repair kit is part #LC146060 in case you need it.

view full answer...

Answer 4

The landing gear looks like a standard set based on the pictures and the dimensions you listed. The part #LC146060 would be what you need for the follow leg and then part #LC146059 for the lead leg.

view full answer...

Answer 5

It sounds like you're trying to replace the motor on your Kwikee steps with the part number 366043, and we have just what you're looking for. In order to replace the motor for these steps you'll want to use the Replacement Motor for…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Follow Leg Repair Kit for 2010 Keystone Laredo 298BH Venture Landing Gear

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching