Are There 5-Lug Hubs for a Military Trailer with Timken 15118 and 09074 Bearings

Question

Question:

I want to change my hubs to a 5 lug, I measured the tapered spindles inner diameter is 30.20 mm outer diameter is 19.20 mm. The bearings currently on it are inner sz Timken 15118 and the outer bearing is a 09074 Timken. Do you have the hubs I would need?

asked by: Kane J

0

Expert Reply:

I do have an option for you but we do not have any 5-lug hubs with the bearings that you listed because they are not common sizes. I don't think you are going to be able to find a new 5-lug hub that uses these bearings because again they are not very common therefore the only option you really have to obtain a 5-lug hub is with a new axle.

For this, I recommend taking a look at the Timbren Axle-Less Trailer Suspension System. This system will be ideal for a military trailer because there is no axle beam so you can take it offroad without many clearance issues. It will also ride pretty much the same unloaded as it would loaded due to the integrated rebound spring. The Timbren Axle-Less Trailer Suspension System is offered in 1,200 - 7,000 lb capacities as well as with 4" drop, straight, and 4" rise spindles.

For example, the Timbren Axle-Less Trailer Suspension System part # A35RS545 has a 3,500 lb capacity, a straight spindle, and comes with 5 on 4-1/2" idler hubs.

expert reply by: Conner L

0

Answer 1

Thank you for the photo of your trailer idler hub and for the details about its bearings. New hubs must use the very same bearing set in order to fit on your spindles. All 6-on-5-1/2-inch idler hubs we offer are shown on the linked page. Timken…

view full answer...

Answer 2

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 11

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Are There 5-Lug Hubs for a Military Trailer with Timken 15118 and 09074 Bearings

Product Page this Question was Asked From

Continue Researching