Replacement Tarp for Truxedo Lo Pro QT for 2006 Toyota Tundra 6 Foot Bed with Bed Caps

Question

Question:

I need to replace the TruXedo Loprofile cover only for 2006 Toyota Tundra crew cab - 6 ft bed with bed cap. What is the replacement part number?

asked by: James

0

Expert Reply:

We have just what you need as the cover you have on your 2006 Toyota Tundra crew cab 6 foot bed with bed cap is the part # TX545101 which means the replacement tarp is the part # TX545101-COVER.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Yes, the correct replacement tarp for the TruXedo Lo Pro QT Soft Roll-up Tonneau Cover part #TX545101 that you have on your 2004 Toyota Tundra with the 6-1/2' bed is the Replacement Tarp for TruXedo Lo Pro QT Soft Tonneau Cover part…

view full answer...

Answer 2

The TruXedo Lo Pro Soft Roll-up Tonneau Cover - Black is the complete cover confirmed to fit your 2002 Tundra. The cover you want is the Replacement Cover for TruXedo Lo Pro Soft, Roll-up Tonneau Cover - Black #TX5681-CVR which comes with the Velcro…

view full answer...

Answer 3

The plastic hook on the Replacement Safety Strap part #TX1115355 which is a fit for the TruXedo Lo Pro QT and TruXedo Deuce 2 Tonneau Covers will secure to a loop on the backside of the cover which you can see in the attached photo.

view full answer...

Answer 4

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 5

Hi Jeff; thanks for the question and sturdy is definitely a good word for the etrailer tonneau that fits your 2022 Ram 1500 with a 5-1/2 foot bed, the etrailer Hard Tonneau Cover #e35DR. It's made of a fiberglass-reinforced plastic which is a…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

If you check out the attached picture you can see where you'll find the serial number and date code on your cover.

view full answer...

Answer 12

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...