Removing Terminals from Winch Quick Disconnect Connectors

Question

Question:

The contacts in the red housing were inside snapped in, how do you remove them so I can clamp the wench leads in place?

asked by: Ron

0

Expert Reply:

Sounds like you are trying to pull the metal contacts out of the quick connect assembly. What you'll need to do is insert a slot screwdriver down into the opening end of the connector with the slot perpendicular to the opening so that you can depress the metal tab that holds the pins into the house and allow you to pull the lead out of the back of the connector.

expert reply by: Jameson C

0

Answer 1

Yes, the Pop & Lock Power Lock Conversion Kit for Truck Caps and Hard Tonneau Covers part #PAL9772 or part #PAL9555 will work on the Leer 100XQ Truck Caps because it uses a cable latching mechanism and the handle is not riveted on.

view full answer...

Answer 2

If the wires from your trailer are good and the power is good, then we just need to figure out what each wire on the light itself does. The best way to do that is to take a 12 volt power supply and apply that to each of the wires on your lights to…

view full answer...

Answer 3

Yes, since all the running/clearance lights on your trailer will be fed by the same circuit you can use butt connectors rather than quick-splice connectors to enable a longer-lasting and more water-resistant connection. Wiring the lights as you…

view full answer...

Answer 4

I recommend wiring your F-150 with the Front #BDW20205 and Rear #BDW20207 wiring kits. Both kits include a connector you can use to mount to the wiring on your Badlands Apex 12000 winch. The front kit includes 7-1/2' of wiring while the rear kit…

view full answer...

Answer 5

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

It sounds like you are asking if a Reese weight distribution system head will fit on a Draw Tite weight distribution shank which the answer to that is yes.

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

From what I could find out about your current circuit board, the Atwood Replacement Control Panel #AT91367 will be a direct replacement.

view full answer...

Answer 10

For your application you need the Air Lift LoadLifter 5000 which has that 5,000 lb weight capacity you mentioned. Please note that suspension enhancement is designed to help the OEM suspension on your 2021 Ford F-250 and won't increase the weight…

view full answer...

Answer 11

The best air bag kit for your 2022 Ford F-350 that has a single rear wheel axle is the part #F95FV which has the 5,000 lb capacity you are wanting. Firestone bags are superior Air Lift bags. The ply rating of the rubber is higher, the attachment to…

view full answer...

Answer 12

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Removing Terminals from Winch Quick Disconnect Connectors

Product Page this Question was Asked From

Continue Researching