Weight of the CargoBuckle G3 Retractable Ratchet Tie-Down Straps # IMF18800

Question

Question:

Hello. Id like to know weight of this strap set, its retail package?

asked by: Michael

0

Expert Reply:

The CargoBuckle G3 Retractable Ratchet Tie-Down Straps # IMF18800 that you referenced is 6 lb and the weight capacity is 1,167 for the working load limit and 3,500 as max break strength.

expert reply by: Jameson C

0

Answer 1

To secure your Polaris ATV to the trailer I recommend taking a look at the CamBuckle G3 Retractable Ratchet Tie-Down Straps #IMF18800. These ratcheting tie-downs can be permanently bolted to your trailer to allow for much quicker (and cleaner)…

view full answer...

Answer 2

If your 1998 Dodge Ram has a factory trailer connector of any kind there will be a connector under the dash to install an electric trailer brake controller like the Prodigy P3 #90195. The adapter to plug into the connector is #3020-P. I've linked…

view full answer...

Answer 3

The best mounting location of Tie Down Strap part #IMF18800 will really depend on what you are carrying. Generally speaking, mounting one tie down at each corner of the bed would allow for the most flexibility. Each strap can safely handle a load of…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Although the Tekonsha Prodigy P3 #90195 and Primus IQ #TK90160 electric brake controllers are very similar they do have some key differences as well. For one the P3 is designed to work with electric and electric over hydraulic brake systems. The…

view full answer...

Answer 10

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Answer 11

We highly recommend against double towing and many states either don't allow double towing or have numerous restrictions. There are some states that limit the total length of all 3 units, some only allow certain types of trailers behind the 5th…

view full answer...

Answer 12

For a 24 inch hitch extender the best option is the Curt part #C45048 cut down to the 24 inch length. This has a capacity of 8,000 lb trailer weight when used with a WD system like you mentioned. Since this is the only extender option that's…

view full answer...

Weight of the CargoBuckle G3 Retractable Ratchet Tie-Down Straps # IMF18800

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching