If Lippert Ground Control 3.0 Loses Power Does it Lose Level Setting

Question

Question:

Is the level location retained if power is removed from the system? I turn the battery switch off when the trailer is in storage to prevent any battery draw from occurring and I am wondering if I will have to reset the level location every time I turn the switch back on to take it out camping.

asked by: Jon

1

Helpful Expert Reply:

I checked with Lippert and if the Ground Control 3.0 part # LC675817 loses power it does not lose the level settings. Once it's set it's set. Here's the example they used:

"The controller is like your home computer or cell phone. Once the level is set, it is set and stored."

expert reply by: Jameson C

1

Answer 1

I spoke to my contact at Lippert about your Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part #LC358590 and they stated to unplug the front jack to create error. Then clear the error. Then manually level coach out. Once manually…

view full answer...

Answer 2

I spoke to my contact at Lippert and they seem to think there is an issue with power either reaching the touch pad or control box. The first thing you will need to do is obtain a multimeter like part #ALL648349 and test the power wire just before…

view full answer...

Answer 3

Sounds like your trailer has the Lippert Ground Control 3.0 leveling system and you are trying to pair the new remote to the system. To enter the remote's configuration menu press the silver button 5 times. On the Lippert Ground Control leveling…

view full answer...

Answer 4

Thank you for the picture of the module your Lippert Ground Control kit has as I can tell from it that you have a 4 point kit. So for a replacement control module you'd want the part #LC304136. The "points" refer to the number of jack…

view full answer...

Answer 5

I reached out to my contact at Lippert and they said that it sounds like you just aren't holding the 4 buttons for the reset long enough. It requires 5 seconds, but many people will count to 5 a little too fast and the system won't reset. He…

view full answer...

Answer 6

Based on your description it sounds like you have the Replacement New-Style Linc Analog Remote - 5 Function #LC292614. In order to sync this remote you need to start by pressing and holding the momentary push button on the receiver. Next, press the…

view full answer...

Answer 7

In order to sync the Replacement Touchscreen Remote part #LC358601 with the multi-function pad on your 2015 Keystone Cougar 327RES you are going to want to complete the following: 1) To begin syncing the remote to the receiver, both the receiver and…

view full answer...

Answer 8

We do have a replacement wireless remote for the Lippert Ground Control 3.0 #LC358590, for that you would want the part #LC358601. Here is how the remote would get programmed: 1. Enter the Leveler app on the LINC Remote. 2. Turn the remote on by…

view full answer...

Answer 9

The pin on your LCI remote #LC358601 can be reset by following these simple steps. Press "home" button to turn on transmitter. Then press and release "home" button 5 times. Then press "config". The screen will ask you if…

view full answer...

Answer 10

It sounds like you need to re-calibrate the zero point on your Lippert Ground Control 3.0 #LC304136 system. Below I've listed out the steps you'll need to follow and will allow you to use the auto leveling again. Zero Point Calibration The…

view full answer...

Answer 11

To configure the remote to the touch pad on a Lippert Ground Control system, #LC358590, you first need to configure the remote as follows: 1. Turn the remote on by pressing and releasing the large silver button at the bottom of the unit. If the…

view full answer...

Answer 12

The 2014 Dutchmen Voltage series 5th wheels that have the Lippert Ground Control Leveling System #LC358590 installed may have the remote sensor unit, shown in the linked photo, behind some type of cosmetic panel. This sensor needs to be positioned…

view full answer...