Could Trailer Hitch Weld Onto Heartland Torque 381 Fifth Wheel

Question

Question:

Can a receiver type hitch be welded on this toy hauler

asked by: Marvin R

0

Expert Reply:

Yes it is possible to weld a hitch to your Heartland Torque 381 fifth wheel trailer, or if you wanted to weld on the Curt hitch part # 13703 you certainly could do that as well. This hitch can fit basically all frame styles between 22 and 72 inches in width.

expert reply by: Jameson C

0

Answer 1

The trailer hitch I recommend for a 2019 Rockwood Roo 233S is the Adjustable Width Trailer Hitch Receiver for RVs part #13703. The Adjustable Width Trailer Hitch Receiver attaches to the frame via two side brackets which will need to either be…

view full answer...

Answer 2

If your RV currently has incandescent lights and you're going to be adding the Triple LED #CE44VR to the mix then you will most likely need to add resistors like the Load Resistor Kit for LED Turn Signals - 50 Watts - 6 Ohm - Qty 2 #DI34ZR to the…

view full answer...

Answer 3

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 12

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...