What Grade Bolts are Included with Tow Ready Lunette Ring # C48550

Question

Question:

What is the grade of the bolts supplied with this Lunette Ring? Thank you

asked by: Nathan

0

Expert Reply:

The Curt Lunette Ring # C48550 referenced in your question requires grade Grade 8 hex mounting bolts like # C48332.

This lunette ring has a 35,000 pound weight capacity and its black powder coated steel will help to protect it against any rust or corrosion. I have attached a short video review on this assembly that you can check out as well.

expert reply by: Chris R

0

Answer 1

You can absolutely trust the manufacturer ratings for the ball mounts we have available, regardless of whether or not they feature a solid or hollow shank. Ball mounts and other towing products are typically tested well beyond their actual listed…

view full answer...

Answer 2

When the shank of a ball mount or hitch-mount accessory - say a bike rack for example - is solid rather than hollow this typically means it will be stronger. It also means it will be heavier. The Brophy Ball Mount #BH20 has a solid steel shank…

view full answer...

Answer 3

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 4

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 9

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 10

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 11

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

What Grade Bolts are Included with Tow Ready Lunette Ring # C48550

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching