Wiring a 7 Pin Connector on a 2004 Jeep Wrangler

Question

Question:

Im installing a 7 pin connector on my 2004 Jeep Wrangler. Should I connect the Aux power wire to constant hot or ignition hot? It says fused battery lead Thanks!

asked by: Aaron

0

Expert Reply:

You will connect the power lead to your positive battery terminal with a 40-amp circuit breaker.

expert reply by: Sarah

0

Answer 1

I have a solution for you. Here at Etrailer, we strongly discourage using wheel-mounted bike racks like the Kuat NV 2.0 #NV22B for bikes with fenders. Mounting wheels with fenders can cause the fenders to crack or become damaged, especially with the…

view full answer...

Answer 2

Most of the time the 4-Way connector is wired as follows. Looking at the front of the socket on the vehicle side with the cover raised the top left pole is the yellow, left turn/brake pole, the top right pole is the right turn/brake pole, the bottom…

view full answer...

Answer 3

Yes, we have exactly what you need. To convert the 4-way of your Jeep to a 7-way so that it will adapt to your trailer that has a 7-way you have two options. If your trailer doesn't have brakes all you would need is the #37185. This would simply…

view full answer...

Answer 4

To get a 7-way for your 2020 Jeep Wrangler 2 door, you will start with the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #118786 and then add the Adapter kit #ETBC7. The 4-way wiring will connect to your factory wiring, and then the…

view full answer...

Answer 5

As long as the fender is tightly installed on the bike and the hook is attached to the fender as close as possible to the top tube of the bike, the #BA22B should carry the town bike you mentioned with no problem whatsoever. I spoke with one of my…

view full answer...

Answer 6

The Kuat Pivot Swing Away Hitch Adapter part #PVP20B can be used with your Thule EasyFold part #TH903202 and will give the rack the ability to swing out and away from the vehicle so that you can access the cargo area. I attached a picture that shows…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Wiring a 7 Pin Connector on a 2004 Jeep Wrangler

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching