Replacement Weld On Jack Recommendation for Boat Trailer

Question

Question:

Trying to find a replacement weld on jack for an Astro bass boat trailer. Would like to find a jack that will work with my existing welded on plate.center hole diameter is ~2

asked by: John

0

Expert Reply:

The weld-on jacks we carry will fit in welded-on mounting plates with specific dimensions and since you mentioned it was about 2 inches the Fulton Round, Snap-Ring Swivel Marine Jack # FTJ120W0301 may work.

It does come with a mounting plate with the dimensions shown in the accompanying photo but will fit if your has similar dimensions.

You did not mention the height, lift or capacity you needed but this jack offers 10 inches of lift and has a 1,200 lb capacity.

expert reply by: Kyle S

0

click to enlarge

Answer 1

The Replacement Coupler Pin Kit for Titan/UFP Brake Actuators part #TK71-764-00 is 3" long x 1/4" diameter. I spoke with Dexter to confirm this for you.

view full answer...

Answer 2

The Fulton Jack #FTJ12000101 has a snap ring pilot hole that measures 2.313 inches.

view full answer...

Answer 3

The hole in the bracket of the Fulton 1200 lb Snap Ring Swivel Jack #FTJ12000101 is 2.55 inches in diameter to accommodate the 2-1/2 inch diameter flange on the trailer mounted bracket that the snap ring attaches to. The 2-1/2 inch diameter flange on…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

According to our research the Fulton Round, Snap-Ring Swivel Marine Jack #FTJ120W0301 will fit as a replacement for your Shelby 5756 boat trailer jack. It will allow you to keep the same bracket that is currently welded-on. You basically need to open…

view full answer...

Answer 7

Based on the information I could find for the DICO 45264 is was popular on ShoreLand'r trailers. This would require the Idler Hub #AKIHUB-545-35-G-EZ-K with the Grease Seal #168255TB used instead of the seal included with the hub. We currently do…

view full answer...

Answer 8

I do have an option for you but the Shelby trailer jack mounting bracket that you have welded to your frame won't be able to be reused with any newer jack. The Shelby trailer jacks did use similar designs in regards to mounting like the…

view full answer...

Answer 9

We have the Fulton trailer jack part #FTJ120W0301 which we know fits the same trailer mount as the Shelby 5856A that you have so this would be our best option for a solid jack with a very easy install. This jack has a 1,200 lb capacity, a wheel…

view full answer...

Answer 10

Based on my research, the Fulton Round, Snap-Ring Swivel Marine Jack #FTJ120W0301 will be a perfect replacement for your Shelby 5756A trailer jack. This jack will allow you to use the existing snap ring jack mount on your trailer for installation.…

view full answer...

Answer 11

The Fulton Round, Snap-Ring Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,200 lbs #FTJ120W0301 provides similar capacity and does have a Snap ring pilot hole diameter of 2-1/2"that lines up with your Bulldog Jack.

view full answer...

Answer 12

The only repair kit we have for your Profile 2000 hand winch is the Winch Ratchet Repair Kit by Dutton-Lainson item #DL70475. If this isn't what you are needing you will have to replace your winch. I recommend the Dutton-Lainson Hand Winch -…

view full answer...

Replacement Weld On Jack Recommendation for Boat Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching