Replacement Master Cylinder Cap Needed for Dico Actuator

Question

Question:

I’m trying to find a master cylinder cap see pic.

asked by: George

0

Expert Reply:

I believe the master cylinder cap you are needing for your Dico actuator is part # T4480701 which fits the common Dico Model 60 actuators. If you don't have a Dico Model 60 actuator please let me know what you have and I can make additional recommendations for you.

expert reply by: Jon G

0

click to enlarge

Answer 1

Sorry to hear about that Tyler, but to answer your question - if your current cap #3876 measures 1 1/2" wide overall and has a 1 1/4" thread diameter then yes both the Replacement Master Cylinder Cap with Diaphragm for Dexter Model 10 and…

view full answer...

Answer 2

It's hard to tell which cap you need exactly from the picture but I measured the caps we have that might work for you. Part #T4480701 for Titan Model 60 actuators measures 1-1/4 inches at the threads like you previously saw. Part #T4830601 for…

view full answer...

Answer 3

If you look at the picture I have included of Replacement Master Cylinder Filler Cap #T4480701 I would say that is coarse threaded. But regardless this cap specifically fits Titan and Dico model 60 actuators and Titan Aero 7500 actuators. If you have…

view full answer...

Answer 4

You are correct that the Replacement Master Cylinder Assembly for Titan Model 60 and Aero 7500 Brake Actuators - Drum #T4395100 you were looking at is the replacement master cylinder for your older 23361. I included a video of the Titan #T4395100 for…

view full answer...

Answer 5

I went out to the warehouse to pull the Replacement Master Cylinder Filler Cap #T4480701 for your older Titan Model 60 Actuator. I was able to find that the rubber piece you described is actually the diaphragm insert that is sealed within the cap.…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Replacement Master Cylinder Cap Needed for Dico Actuator

Product Page this Question was Asked From

Continue Researching