Manual for Hopkins Reliance Trailer Brake Controller

Question

Question:

Just bought a truck with this product installed to control brakes on a 2-horse trailer. Do you have a user manual or guide I can get as a download? Chevy 2006 Silverado 2500HD. Has tow package.

asked by: Steve K

0

Expert Reply:

I have attached an image of the installation/owner's manual for the Hopkins Reliance Brake Controller model 47285 that you can take a look at. Please just let me know if you have any specific question with regards to its operation and I will be happy to help!

expert reply by: Chris R

0

click to enlarge

Answer 1

The MaxxFan #MA00A04401K would be a good replacement fan for most any camper. It fits a standard 14X14" opening and features 4-speed exhaust fan, manual lift design, removable bug screen and sealed motor. A new inside ceiling trim piece…

view full answer...

Answer 2

I would discourage the use of an adapter for use of 2 inch accessories in 1-1/4 inch trailer hitch receivers. The reason is that the adapter places the carrier farther away from the rear of the vehicle and hitch, creating additional torque that 1-1/4…

view full answer...

Answer 3

The traditional wire colors for brake controller installation are white for ground, black for 12 volt power, red for stoplight switch, and blue for brake output. For more information on wiring in a brake controller check out the help article I…

view full answer...

Answer 4

The Optronics Clearance or Side Marker Trailer Light #MC68AB and #MC68AB are the same size as the Grote 9015 lights. Unfortunately they are not available from the manufacturer with a LED light. You can change the incandescent bulb to an LED Bulb…

view full answer...

Answer 5

Some trailers do have shock absorbers; it isn't all that common but is gaining popularity, mostly among camping trailers. The main reason it's not too common is most people aren't worried about the ride being that smooth. Usually the…

view full answer...

Answer 6

The rule of thumb for estimating a tongue weight is 10-15 percent of trailer weight. A 4,600 pound trailer would have a tongue weight between 460 and 690 pounds. Somewhere between a 1,000 to 2,000 pound capacity jack would be fine. Having a jack that…

view full answer...

Answer 7

This isn't the first time I've heard of this type of issue. It sounds like the functions of your trailer wiring are not synced with your truck. Because you have used two trucks, the issue appears to be with the trailer. I've attached a…

view full answer...

Answer 8

The 7-way connector of the Universal Installation Kit for Trailer Brake Controller #ETBC7 that you referenced uses the blade style pins which are very common in RV applications. The pin style is common in the heavy duty world but is not nearly as…

view full answer...

Answer 9

You'd want to use the 20 amp circuit breaker like #PK54220PL unless your trailer has more than two brake axles. If that's the case you'd want to use the 30 amp breaker #38630.

view full answer...

Answer 10

Since the Hopkins Reliance Trailer Brake Controller you mentioned is a time delayed trailer brake controller, it can be mounted at any angle. Proportonal controllers require a specific mounting angle as the internal inertia sensor requires it to be…

view full answer...

Answer 11

You are correct, you should only be getting output when the brake is applied, or the override switch is activated. It sounds like the controller might be bad, but to make sure, you should probably bench test it before tossing it. Use a circuit…

view full answer...

Answer 12

The difference is the size wheel each would fit. Center Cap #AM90092 is designed for 16 inch diameter wheels with 6 or 8 hole bolt patterns. Center Cap #AM90091 is designed for 15 inch wheels with a 5 hole bolt pattern.

view full answer...

Manual for Hopkins Reliance Trailer Brake Controller

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching