Dimensions of Replacement Rubber Strips for Crossbars

Question

Question:

What are the measurements, especially of the snap ininch lips? I am looking for replacement rubber strips for car top load bars.

asked by: Helmut M

0

Expert Reply:

The Replacement Rubber Strip for Ladder Rack TH376 # 853-3544-23 fits a channel that is 0.443 inches wide at lip. This is 70-1/2 inches long and is a thicker material.

expert reply by: Jason S

0

click to enlarge

Answer 1

Yes, I confirmed with Yakima that the Yakima Crossbar Pads for Aero Crossbars - 30" Long - Qty 2 #Y07413 will fit on your Overhaul HD crossbars.

view full answer...

Answer 2

I may have a solution for you but if you have the Model 3 roof rack by Tesla on your 2020 Tesla Model 3, then we do not have a channel cover specifically designed to fit your roof rack. If the opening in your roof rack is open then it will cause some…

view full answer...

Answer 3

We do have what you need, but the Replacement Rubber Strip for Thule Aero Load Bars #TH853354407 is not the correct part for the ProBars. I contacted the manufacturer regarding the correct replacement rubber strip for your Thule ProBar Evo's and…

view full answer...

Answer 4

The Replacement Rubber Strip for Ladder Rack TH376 - #853-3544-23 fits a channel that is 0.443 inches wide at lip. This is 70-1/2 inches long and is a thicker material. This strip is just about 1" wide total. I've linked a photo that shows…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Dimensions of Replacement Rubber Strips for Crossbars

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching