How Much Does the Draw-Tite Front Hitch for a 2019 Jeep Wrangler Unlimited Weigh

Question

Question:

What is the installed weight of the hitch? Towing is always about weight. Thanks

asked by: Kenneth

0

Expert Reply:

The Draw-Tite Front Mount Trailer Hitch Receiver part # 65079 which is a fit for your 2019 Jeep Wrangler Unlimited weighs 20 lbs. I have also attached a photo of what it will look like once installed.

expert reply by: Conner L

0

click to enlarge

Answer 1

The Equal-i-zer Weight Dist Shank part #EQ90-02-4600 should allow you to tow with the tailgate down on your 2017 Ram 3500. I have attached a photo for you of this shank used with a similar system on a similar truck

view full answer...

Answer 2

To add a front mounted hitch to your 2023 Jeep Wrangler Unlimited, I recommend the Draw-Tite Front Mount Trailer Hitch item #65079. This hitch is custom fit and bolts to your Jeep with included hardware. This front mounted hitch has a 500 lbs…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 5

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 6

Since the issue appears to be on the vehicle side for your 2017 Toyota Tacoma, I recommend first checking the connector itself. Look to see if there is any dirt or corrosion built up inside the connector that may preventing a solid connection with…

view full answer...

Answer 7

The 1-7/8 inch width is what is rounded up to 2 inches which is a standard width for winch straps. The 14 foot length is not something we carry. I recommend the Hand Winch Strap with Safety Hook, 2" Wide x 15' Long - 4,000 lbs #DL24239 or…

view full answer...

Answer 8

view full answer...

Answer 9

The #37213635 JR Products Replacement Landing Gear Switch you'd mentioned would be a proper replacement for your existing Atwood 70254 landing gear switch. If you wanted the switch, wiring harness and the bezel for the switch, use the Stromberg…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The 18.5x8.5-8 is actually an old tire size that is not used much anymore. The closest metric size to your existing tire would be 215/60-8. Your wheel most likely has a 5-on 4-1/4 inch bolt pattern (see link), you will want to make sure that the bolt…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

How Much Does the Draw-Tite Front Hitch for a 2019 Jeep Wrangler Unlimited Weigh

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching