What Size Hole Is Furrion Power Inlet # F30ITSSS Designed to Fit

Question

Question:

What size hole saw is needed for the install of this?

asked by: Steve W

0

Expert Reply:

The Furrion Power Inlet # F30ITSSS that you referenced is designed to fit in a hole that is 2-1/2 inches in diameter.

expert reply by: Jameson C

0

Answer 1

The wattage of 50-amp service is: 50A x 120V x 2 = 12,000 watts so you would need to parallel another inverter generator rated for at least 5,000 watts to your Honda EU7000iS inverter generator to have a sufficient amount of power to run both…

view full answer...

Answer 2

For 30 amps like what the Progress Dynamics RV Power Control Center with AC/DC Panel and Converter/Smart Charger #PD4135K is rated for you'd need to use 10 gauge wire minimum if made from copper or 8 gauge if made from aluminum. For a new socket…

view full answer...

Answer 3

I checked with Furrion and the cover by itself is not an available replacement part, so to get that cover you would need to get the whole inlet: - Furrion 50 Amp RV Power Inlet - 125V/250V - LED - Square - Black #F52INSBS I have added a link below to…

view full answer...

Answer 4

I can definitely understand not wanting to re-size your current 2-1/2 inch hole, but the smallest size hole that will allow a 30 amp rv power inlet is 2-1/2 inches in diameter, so that would be the smallest hole size you would need. For that you…

view full answer...

Answer 5

I went out to the warehouse and measured Epicord 30 Amp Twist Lock Power Inlet - Black Item #277-000138 for you. The overall width is 3-1/4 inches. the overall height (lid closed) is 4 inches or 7-1/2 inches with the lid opened straight up. The…

view full answer...

Answer 6

While we don't have an online set of instructions for the Epicord 30 Amp Twist Lock Power Inlet #277-000137 I can link you I can give an even better source for install info with a step by step install video link. I attached a link to this page…

view full answer...

Answer 7

The rear portion of the Epicord 30 Amp Twist Lock Power Inlet - White #277-000137 that you referenced is 3 inches so a hole diameter of 3-1/4 inches would easily work. I attached an install video for this for you to check out as well.

view full answer...

Answer 8

If you have a typical hole saw set, then you will want to use a 3" hole saw on the Epicord 30 Amp Twist Lock Power Inlet, #277-000138. The outer diameter of the socket that mounts in the RV wall is 2-7/8 inches. If you wanted to be very precise,…

view full answer...

Answer 9

Once it's disassembled, once you access the rear of the socket you'll see that it's color coded as shown in the provided photo. The corresponding plug, like #A10-30FDT would wire in the same manner. The screws on each terminal are color…

view full answer...

Answer 10

Sounds like you are looking for something like the Furrion Replacement RV power inlet part #F30ITSSS which uses a ring lock and is also made of stainless steel. I attached a review video for this for you to check out as well.

view full answer...

Answer 11

To install the Mighty Cord Replacement RV Power Inlet #A10-30INVP that you referenced requires you to install a 2-7/8 inch diameter hole. That would be the size hole saw you would need.

view full answer...

Answer 12

The Epicord 30 Amp Twist Lock Power Inlet #277-000138 has it's own waterproof cover. The Weatherproof Cover w/ Threaded Ring #A10-30CV is designed to fit a Twist Lock 30 amp connector like the part #A10-30FDT.

view full answer...

What Size Hole Is Furrion Power Inlet # F30ITSSS Designed to Fit

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching