Installation of 1981 Ford Bronco Replacement Side Mirror KSH3661

Question

Question:

Gents, Seeking replacement mirror and have looked EVERYWHERE. The mirrors I currently have contain 3 holes on rhe upper bracket. Can I send you a pic to help match my mirror?

asked by: Bryan L

0

Expert Reply:

Thank you for your photo.

We offer the K-Source Replacement Side Mirror # KSH3661 for your 1981 Ford Bronco; this is the item you referenced in your question. The top bracket does have only 2 holes, not 3, but it would be easy enough to drill the 3rd hole if you wish. The mirror will be fine if installed with just the two holes that are pre-drilled.

Each hole is 1/4-inch in diameter and they are spaced apart by 3-1/2-inches on centers.

expert reply by: Adam R

0

click to enlarge

Answer 1

The mirror housing of the K-Source Replacement Side Mirror #KSH3661 that you mentioned is made of a plastic with a chrome finish.

view full answer...

Answer 2

I was able to confirm with my contact at K-Source that the mounting brackets on the #KSH3661 are approximately 9" apart from top to bottom. Additionally the mounting holes on the top bracket are 3-3/4" apart and the bottom are 2-5/8"…

view full answer...

Answer 3

The distance between the upper mounting bracket holes of the K Source mirror part #KSH3661 is 3-1/2 inches.

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 5

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 6

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 7

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 8

A cover being installed on your spare tire would not prevent the Swagman Bike Rack part #S80501 from installing. The rack would still fit and work well. You might still compare the dimensions in the picture I attached with you spare tire so that you…

view full answer...

Answer 9

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

Most critical to trailer tire performance and durability are 1) proper inflation 2) observance of the tire's rated load capacity and 3) observance of the tire's speed rating. If either of these factors is off the mark then the tire will tend…

view full answer...

Answer 12

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Installation of 1981 Ford Bronco Replacement Side Mirror KSH3661

Product Page this Question was Asked From

Continue Researching