What Prevents DeeZee Truck Bed Mat # DZ87012 From Flying Out of Truck Bed

Question

Question:

Any chance this product could fly out of the bed at highway speeds? What keeps it in place?

asked by: Joseph C

1

Helpful Expert Reply:

The weight and how well the DeeZee Custom-Fit Truck Bed Mat # DZ87012 fits the bed of the truck is what keeps it from flying out. The mat weighs 55 lbs and is custom fit for the bed of the truck which prevents air from being able to get underneath it.

expert reply by: Jameson C

1

Answer 1

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

I recommend going with the Air Lift LoadLifter 7500 XL Ultimate Air Helper Springs #AL89DQ for hauling around an in-bed camper with your 2024 Ford F-350 Super Duty. I really like this kit because it has the higher 7,500 lb rating (which you don't…

view full answer...

Answer 5

Since you are pulling a trailer that weighs around 8,500 lbs. you would just want to stick with the Firestone Ride-Rite Air Helper Springs #F35FV (5,000 lb.). You really only need to spend more for the Firestone Ride-Rite Red Label Extreme Duty Air…

view full answer...

Answer 6

Here is a list of the bump stop replacements we have which fit your 2024 Ford F-350. If you can tell me how you plan to use your F-350 I can give you my personal recommendation for the option which works best for you. Timbren Front 2WD #TFF350SD2 4WD…

view full answer...

Answer 7

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

Hey Robert, sorry it can be a bit confusing navigating all those facets for the camper tie downs, but I did go ahead and find those tie downs you were looking for. For the front, you'll want the TorkLift Camper Tie-Downs #TL87CR (TorkLift P/N…

view full answer...

Answer 11

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

What Prevents DeeZee Truck Bed Mat # DZ87012 From Flying Out of Truck Bed

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching