Replacement Motor Recommendation for Atwood Motor Kit 75367

Question

Question:

My electric motor for ‘02 gooseneck horsetrailer dual jacks is an Atwoods 75721, been told by our RV place the replacement is Atwood 75367 or Lipper who bought them out 678265. Hard to find old stock The motor does measure 8 1/2” , 4 1/8 to mount holes . I assume it is a5000lb motor .

asked by: Jan D

0

Expert Reply:

Those part numbers mentioned are older but we do have the motor you are looking for as the part # LC142178 which is the same replacement motor as you need.

expert reply by: Jameson C

0

Answer 1

The Lippert HD 6500-lbTuson 5th Wheel RV Landing Gear Motor #LC196308 will indeed fit your landing gear without modification. It will have the same bolt pattern as the #LC142178 you currently have, but will definitely have a higher capacity. If you…

view full answer...

Answer 2

Lippert landing gear parts are sold under other brand names as well, such as Stromberg Carlson, Venture and Atwood, and often an alternate part fits and works perfectly well. You'll just want to match the length of the original lead/driver…

view full answer...

Answer 3

What you described does sound like a damaged gear box. This is pretty common for Venture landing gears like what you said you have and the correct solution is a new gear box which the part #LC276602 is the correct replacement for. For a replacement…

view full answer...

Answer 4

Glad to hear how pleased you are with the Lippert landing legs #LC179013 and #LC179014! I spoke to my contact at Lippert and he recommended a white lithium grease like #L11354 for the zerk fitting for the gears and a silicone based lubricant on the…

view full answer...

Answer 5

I reached out to Lippert and while they were unable to provide the gear ratio of the Lippert #LC276602 gearbox, they could confirm that the motors used with these are 3:1. Because of that, the gearbox should be somewhere around there, but again- they…

view full answer...

Answer 6

It is possible that there is a part number somewhere that would help identify the landing gear on your trailer. Sometimes there is information on the underside of the caps on the tops of the jacks so that is another place you can check if you…

view full answer...

Answer 7

It could be the motor but it could also be the screw/nut inside the jack leg that is causing the problem. Since you mentioned that it is hard to crank it manually I suspect that it is likely the screw and/or nut. On jacks that have an ACME screw the…

view full answer...

Answer 8

The sure way to pick out replacement landing gear for a trailer that will bolt right up to the current brackets is to measure the distance between the mounting brackets (underside of top bracket to top of lower bracket as shown in the diagram) if it…

view full answer...

Answer 9

In the past we have had customers use the Replacement Gearbox part #LC276602, Lead Leg Leg Repair Kit part #LC146059, and Follow Leg Repair Kit part #LC146060 on the Atwood landing gear legs with success but it would be hard for me to confirm fit…

view full answer...

Answer 10

The correct replacement motor for your landing jack is the Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor #LC141893. The Atwood brand was discontinued and bought by a couple companies for their product lines. Lippert absorbed…

view full answer...

Answer 11

It sounds like you need a new gearbox for your Atwood landing gear. I recommend the all-aluminum Lippert gearbox #LC276602 which works as a replacement for most brands of landing gear including Atwood, Lippert, and Stromberg-Carlson. The gearbox…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Replacement Motor Recommendation for Atwood Motor Kit 75367

Product Page this Question was Asked From

Continue Researching