Suspension Enhancement Recommendation for 2018 Ford Expedition

Question

Question:

What suspension enhancement should I get for my 2018 Ford Expedition? My suspension sags when I tow my trailer and I want to level it.

asked by: joe s

0

Expert Reply:

For your 2018 Ford Expedition the suspension enhancement kit I recommend is the SumoSprings part # CSS-1168R because this kit installs easily in the coils of your rear suspension and does not require air pressure maintenance. It also will reduce the rear suspension sag in your vehicle greatly when you are towing.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Coil SumoSprings Custom Helper Springs for Coil Spring Suspension part #CSS-1168F which are a fit for a 2021 Ford Expedition will help the coil springs from compressing which will in turn prevent sag/squat. There will only be one spacer per side…

view full answer...

Answer 2

All 3 options are the same Coil SumoSprings: #CSS-1168 #CSS-1168R #CSS-1168F The difference in the part numbers just has to do with R is for rear, F is for front and then we have the regular number in case someone is looking for the part to fit a…

view full answer...

Answer 3

Rubber jounce springs like the Timbren #TDR1525H2 that you referenced help support your suspension when it is under load, but otherwise do not affect ride quality (a good thing). They do not add height to your suspension. Do please note that the kit…

view full answer...

Answer 4

I spoke with Super Springs about the Coil SumoSprings Custom Helper Springs part #CSS-1168R for your 2016 Ford Expedition. The issue is not that it is not a fit but rather they have not yet had a 2WD model in to test them on. Therefore, in order to…

view full answer...

Answer 5

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 6

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

A cover being installed on your spare tire would not prevent the Swagman Bike Rack part #S80501 from installing. The rack would still fit and work well. You might still compare the dimensions in the picture I attached with you spare tire so that you…

view full answer...

Answer 12

We have one option that will work for you. The Trailer Hub and Drum Assembly - 4,400-lb E-Z Lube Axles - 10" Diameter - 6 on 5-1/2 #8-407-5UC3-EZ uses inner bearing #L68149 and outer bearing #LM67048 so it would work perfectly on your spindle.…

view full answer...

Suspension Enhancement Recommendation for 2018 Ford Expedition

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching