Bearing Buddy Compatibility with Dexter 6000 lb Axle

Question

Question:

Dexter 6000# axle bearing buddy Mine has a 6.68 ID What part # is used for that?

asked by: DAN A

1

Helpful Expert Reply:

I'm assuming there is a typo in the ID you gave. Based on the Dexter 6K hubs, it appears you may have a 2.72 grease cap. That is the closest I found to the size you gave. The Bearing Buddy Bearing Protectors - Model 2717 - Chrome Plated (Pair) # BB2717 would be the fit for that model.

If you can give me the numbers on your hub, I may be able to pin point the correct kit for you if there is one.

expert reply by: Jason S

1

Answer 1

EZ Lube axles like the item #T3584F-EZ-8974 come from the factory with just a little bit of grease in the bearings. The first time you use the EZ Lube feature to fill the axle, it will take a lot of grease. You will probably use 3/4 to a full tube…

view full answer...

Answer 2

EZ Lube Dust Caps, like #DC200L-DCRP, have a rubber plug that can be removed to access the zerk fitting. The rubber plug can be removed by gently prying it up with a flathead screwdriver. If your dust cap is in good condition and you want to avoid…

view full answer...

Answer 3

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Answer 4

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

We may have a grease seal that will work in your application however, my research had conflicting measurements for the Hadco 3122 that you referenced. I contacted my technical contact at Redline to verify that the Redline Grease Seal #1105-100-031…

view full answer...

Answer 7

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

We have a really great kit that comes with everything you'd need to convert your 2021 Vanleigh Pinecrest 335RLP from tandem 6k drum brakes to electric over hydraulic disc brakes with the HydraStar Disc Brake Kit w/ Actuator for Triple Axle…

view full answer...

Answer 11

As long as the RBW Lil' Rocker mounts to industry standard base rails you'll need the Curt Adapter Rails #C29BR that fit in the OEM puck system on your 2019 Ram 2500 and give you a standard base rail connection. I'm attaching a photo…

view full answer...

Answer 12

Hey Mark, from previous customers we have determined that the your 2009 Coachmen Chapparal M-278 has a Lippert 1621 pin box so the Gen-Y Gooseneck adapter part #GY58GR would fit and work great on it. This will give you a cushioned gooseneck adapter.…

view full answer...

Bearing Buddy Compatibility with Dexter 6000 lb Axle

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching