Dimensions for Thule Roof Cargo Box Support Plate

Question

Question:

Hi, what are the dimensions of this plate?

asked by: Da

0

Expert Reply:

The Replacement Plate Box Support for Adventurer Cargo Box # TH10378 is 5-1/2 inches long and 2-1/2 inches wide with holes that are 5/16 inch diameter 4 inches on center. I've attached a photo to help further.

expert reply by: Jason S

0

click to enlarge

Answer 1

I went to the warehouse and took a look at the Replacement Mounting Hardware for Thule Weekender Cargo Box #1032802, and it does in fact have 8 bolts.

view full answer...

Answer 2

I spoke to my contact at Thule and she told me that there were a couple different generations of the Sears Sport 15-CAV and they have replacement lock hardware that would work for one of the generations, but without knowing what generation you have…

view full answer...

Answer 3

The u-bolts that are included in the Thule Replacement Hardware Kit #TH05603 referenced in your question have a width of 4-3/16 inches from outside to outside. I have included an image that labels the dimensions for you to check out. The hardware kit…

view full answer...

Answer 4

For a replacement lock for your Sears X Cargo 20, you might be able to use the Replacement Lock Core and Key #SR03807. Ensure that your current lock resembles this one for this to work.

view full answer...

Answer 5

To replace the mounting hardware on your Sears X-Cargo Sport 20 cargo carrier you can use the Replacement Hardware Kit #TH05603 to re-mount your cargo carrier on most factory and aftermarket roof rack crossbars. To replace the lock, you'll want…

view full answer...

Answer 6

If you order 2 sets of the Replacement Lock and Key for Car Top Cargo Roof Cargo Box - 2824 part #CTC-CAMLOCK-18M-2824 then you will get 2 of the same locks and matching keys. However, they are replacement locks for the Car Top Cargo Roof Box so i…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Dimensions for Thule Roof Cargo Box Support Plate

Product Page this Question was Asked From

Continue Researching