Is Draw Tite Hitch for 2019 Subaru Ascent Concealed When Not in Use

Question

Question:

Will the drawtite hitch be concealed behind the plastic bumper when not in use? Thanks

asked by: Michael K

1

Helpful Expert Reply:

Yes, the Draw Tite hitch # 76253 that fits your 2019 Subaru Ascent will be concealed behind the rear bumper panel when not in use.

expert reply by: Jameson C

1

click to enlarge

Answer 1

The Swagman G10 2-Bike Platform Rack S64682 (discontinued) you purchased from us measures 18-1/2" from the center of the hitch pin hole to the closest part of the rack when folded down, and then 5" for that same measurement when folded up.…

view full answer...

Answer 2

On Curt ball mount #C45446 from the center of the ball hole to the nearest vertical part of the ball platform is approximately 3 inches. This ball mount has a 1-1/4 inch ball hole so if you wanted to use a ball with a 1 inch shank you would need to…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Is Draw Tite Hitch for 2019 Subaru Ascent Concealed When Not in Use

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching