Replacement Fan Blade for Ventline Roof Vent Fan

Question

Question:

Hello, I have a 291rkl springdale keystone not sure what year with a broken fan blade in the restroom. Trying to find a replacement but cant find which diameter size to purchase. The motor says “HC385MG, VD218 105A, 13.6V 1.2A, 3f0622 b7” can you help me?

asked by: YoungMin

0

Expert Reply:

For starters, you are going to want to measure how long the motor you have now is from from end to end (excluding shafts and mounting hardware). You will need to remove the screen in order to do this. If the motor is 1-1/2" long then you have the new motor and can just use the Replacement Fan Blade for Ventline Ventadome part # BVD0215-00. However, if the motor you have now measures 2" long then this is the old motor and they do not make a fan blade that fits it so you would need to replace it with the Replacement 12V DC Motor part # BVD0218-00 and then use the above fan blade.

expert reply by: Conner L

0

click to enlarge

Answer 1

Yes, the Replacement Fan Blade for Ventline Ventadome Trailer Roof Vents #BVD0215-00 would be a fit for your Ventline Ventadome RV roof vent.

view full answer...

Answer 2

We have a couple of 6 inch fan blades that may work for your application, but none of them have the D shaft. Depending on the diameter of that shaft, these may still work. The Replacement Fan Blade for Ventline Ventadome Trailer Roof Vents…

view full answer...

Answer 3

Motor #BVD0218-00 should be the correct replacement. The motor comes with new wires, a bracket, and hardware. The screws that hold the motor to its bracket can be accessed by removing the fan blade. It should just pull off of the motor shaft. You…

view full answer...

Answer 4

Could be as simple as a wiring issue. You may have some corrosion on the wires that run to the motor of your Ventline fan and pushing on them moves the wires enough that they make solid contact. I'd inspect the wiring and see if just wiggling the…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Replacement Fan Blade for Ventline Roof Vent Fan

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching