Handle Diameter of Bulldog Replacement Sidewind Handle # BD500105

Question

Question:

What is the diameter of this handle. Looking for 12mm

asked by: Patrick

0

Expert Reply:

The Replacement Sidewind Handle # BD500105 referenced in your question features a handle diameter of a 1/2 inch, so just over 12mm (0.47 inch). We do not currently have a sidewind handle available that features a diameter of exactly 12 mm.

If you can tell me what model trailer jack you have I will be happy to see if we have the correct replacement handle available or if we might be able to obtain it.

expert reply by: Chris R

0

Answer 1

Those are going to be a taillight adapter that was most likely produced solely by Shasta for your camper. It's primary purpose is to give the taillights a better mounting surface and place to conceal the wiring. It is similar to the Wedge…

view full answer...

Answer 2

The Fulton Replacement Sidewind Jack Handle #F0933305S00 that you referenced has a pin diameter of a 1/2 inch. I have attached an image with this and some additional measurements labeled that you might find helpful when determining if this will work…

view full answer...

Answer 3

Thanks for the pictures! It looks like you have a Ram side wind jack and we do sell replacement parts for it. The jack you were looking at would be a great replacement for it if these parts do are not what you are looking for. The etrailer Square…

view full answer...

Answer 4

The distance from the center of the retaining pin hole to the end of the shaft on the part #BD500105 measures 3 inches.

view full answer...

Answer 5

I measured the Replacement Sidewind Handles #MJ-1000B-HD and #MJ-1500B-HD and found that they both have a diameter of 1/2" and part MJ-1000B-HD measures 2" from the end of the handle to the center of the pin hole while part MJ-1500B-HD…

view full answer...

Answer 6

I went to the warehouse and took a measurement of the Sidewind Handle for etrailer and Ram Square, Direct Weld Jacks, part #TJD-7000S-HD. The handle diameter is 1/2-inch. I have attached a photo of the handle with the dimension shown you can check…

view full answer...

Answer 7

You can run the 12 volt power circuit of your trailer wiring to as many batteries as you like and it will put a light maintenance charge on them that will basically keep them topped off if they were fully charged. Even charging one battery like this…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Handle Diameter of Bulldog Replacement Sidewind Handle # BD500105

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching