Replacement Tongue Jack for a Down To Earth 6x10 Utility Trailer
Question:
The jack you suggested is way too long---the retracted length on your suggested one is 16" ----my old one is closer to 10" from centerline of the mount to the base !! The rest looks good. Got a shorter one whit the 2 1/2" mount hole ??
asked by: Norm
Expert Reply:
For your Down To Earth Trailer, I recommend the Round Snap Ring Swivel Jack w/ Footplate part # TJB-2002-B. This jack uses a snap ring swivel bracket with a 2-1/2" outer diameter. It should work with the existing bracket you have on your trailer now but if not it comes with it's own bracket that you can use if the need arises. This jack has a 2,000 lb tongue weight lift capacity with 15-1/4" of travel. It also comes with a footpad for stability.
I have attached a review video for you as well.
Products Referenced in This Question
Round Snap Ring Swivel Jack w/ Footplate - Weld On - Zinc - Topwind - 10-1/2" Travel - 2K
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 1001 - 2000 lbs
- Swivel Jack
- Topwind Jack
- 11 Inch Lift
- Weld-On
- With Rectangle Foot
- etrailer
more information >
Product Page this Question was Asked From
Round Snap Ring Swivel Jack w/ Footplate - Weld On - Zinc - Topwind - 15-1/4" Travel - 2K
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 1001 - 2000 lbs
- Swivel Jack
- Topwind Jack
- 15 Inch Lift
- Weld-On
- With Rectangle Foot
- etrailer
more information >
Continue Researching
- Shop: Round Snap Ring Swivel Jack w/ Footplate - Weld On - Zinc - Topwind - 10-1/2" Travel - 2K
- Shop: Bearing Buddy Bearing Protectors - Model 1980A w/ Auto Check - Chrome Plated (Pair)
- Shop: Bearing Buddy Bearing Protectors - Model 1980A-SS w/ Auto Check - Stainless Steel (Pair)
- Shop: Round Snap Ring Swivel Jack w/ Footplate - Weld On - Zinc - Topwind - 15-1/4" Travel - 2K
- Shop: Curt Round, Snap-Ring Swivel Jack - Weld On - Topwind - 15" Lift - 2,000 lbs
- Q&A: What Is The Retracted Height Of the Curt Round Top Wind Snap-Ring Swivel Jack # C28304?
- Q&A: Solution for Installing Curt Jack # C28304 on Trailer In Place of Snap Ring that is Different Size
- Search Results: snap ring trailer jack
- Search Results: bearing buddy
- Shop: Stromberg Carlson Trailer Tray Cargo Carrier for A-Frame Trailers - 300 lbs
- Shop: Dexter Idler Trailer Axle w/ Hubs - EZ-Lube - 5 on 4-1/2 Bolt Pattern - 60" Long - 2,200 lbs
- Q&A: Will a 175/80-13 Trailer Tire and Wheel Fit in Place of a 5.30-12 Trailer Tire and Wheel
- Q&A: Diameter of Mounting Bracket Hole on Round Snap Ring Swivel Jack
- Video: Dexter Trailer Springs Over-Under Conversion Kit Installation K71-384-00
- Q&A: Can Trailers Have Shock Absorbers Installed
- Shop: Trailer Hitch
- Search Results: 44649
- Article: Most Popular Wheel Bearings
- Q&A: Recommended Replacement for Atwood Surge Brake Actuator 85778
- Q&A: Recommended Dexter Suspension Kit 7753400
- Video: B and W Hitch Ball - Trailer Hitch Ball - BWHB94005 Review
- Shop: Trailer Wiring
- Search Results: 25580
- Article: Trailer Wiring Diagrams
- Shop: Brake Controller
- Video: Timbren Axle-Less Trailer Suspension System Installation
- Search Results: 68149
- Article: Trailer Tire Sizing
- Video: Choosing the Right Trailer Wiring
- Search Results: dust cap
Norm
10/18/2018
The jack you suggested is way too long---the retracted length on your suggested one is 16" ----my old one is closer to 10" from centerline of the mount to the base !! The rest looks good. Got a shorter one whit the 2 1/2" mount hole ??