2-1/2 Inch Diameter Red Round Trailer Clearance Light with Reflective Housing

Question

Question:

does this have reflectivity? # MC56RB?

asked by: Me

0

Expert Reply:

I do have a similar clearance light for you with a reflective housing but the Trailer Clearance or Side Marker Light part # MC56RB does not. Instead, you will want to take a look at the Trailer Clearance or Side Marker Light part # MCL59RB for LED or part # MC57RB incandescent. Unfortunately, these lights are only available with a recessed mount part # A55GB. You are also going to need to use the pigtail part # A46PB.

expert reply by: Conner L

0

Answer 1

The part #MC56RB is a 2-1/2 inch light. For a similar dimension amber clearance light we have the part #MC58AB but this is a surface mount light.

view full answer...

Answer 2

The #MC56RB you were looking at is designed to fit in a 2-3/4" diameter hole and will have mounting holes 2-11/16" apart, so these will work for your 2011 PJ Dumper trailer. If you also need new pigtails for the wiring, you can use the…

view full answer...

Answer 3

Other than saying that the air bags need to be kept between 5 and 100 psi, Firestone does not offer much in the way of specifics. The instructions mention that as a general rule of thumb, 1 psi will support approximately 40 lbs of load. Your best bet…

view full answer...

Answer 4

We do have air bag helper spring options available for your 2008 Ford F-250. Firestone Ride-Rite kit #F2550 will fit 2- and 4-wheel drive models (will not fit on SuperCab V10 models with 8 foot bed.) I have included a link to a video showing…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR which will be 3/8" shorter but that is still close…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 11

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 12

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

2-1/2 Inch Diameter Red Round Trailer Clearance Light with Reflective Housing

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching