Does Redarc In-Vehicle BCDC Battery Charger # 331-BCDC1240D Require Shore Power

Question

Question:

How would I add shore power/ generator charging to the Redarc bcdc1240 installation? Seems like all I need is a 12-15 volt power supply. Thanks

asked by: Paul R

0

Expert Reply:

The Redarc In-Vehicle BCDC Battery Charger # 331-BCDC1240D that you referenced does not have a way to run AC/shore power to it. It takes all DC, 12-volt style power sources.

expert reply by: Jameson C

0

Answer 1

I reached out to my contact at Progressive Dynamics and he said that you can use the Mighty Mini AC/DC Panel and Converter/Smart Charger #PD4045KA at the same time as your solar MPPT charge controller, but your solar needs to be connected directly to…

view full answer...

Answer 2

The Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger #PD4045KA that you referenced only accepts AC power to then convert to a 12 volt charge for your batteries. You could bypass this and run a charge line from your 7-way to…

view full answer...

Answer 3

To charge your batteries on your 2015 Lance 1575 from your vehicle or solar power and that is compatible with lithium batteries, I recommend the The Manager30 Battery Management System with Lithium Profile Item #RED88FR and the Pollak…

view full answer...

Answer 4

You can definitely replace the torsion axle on your trailer with a Timbren Axle-Less Trailer Suspension System like the 3,500 pound #ASR3500S04 referenced in your question. Since you will be replacing your axle, the easiest way to install this system…

view full answer...

Answer 5

In order to find the correct replacement axle for a trailer you'll need to know the axle capacity, spring center length, and hub face length. The lengths are usually found on the axle tag with the axle capacity in the form of "HF=" or…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Hey Richard, thanks for reaching out! The Air Lift LoadLifter 7500 XL Air Helper Springs #AL57541 does take up the same space as the Curt 19419346 5th wheel bracket kit for your 2024 GMC Sierra 3500. The only way to remedy this is to use the…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The best hitch receiver for hauling a bike with your 2022 Subaru Ascent is going to be the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" item #C25VR. This hitch receiver mounts behind your rear bumper bar instead of below your…

view full answer...

Answer 11

I have attached a chart you can check out that describes the torque needed per wheel size, wheel stud size and material. For an 8-inch wheel with a 1/2-inch wheel stud the torque is 75 to 86 ft-lbs. For a 15 inch steel wheel with 1/2 inch wheel studs…

view full answer...

Answer 12

The wheels for your ST215/75R14 sized tire on your 2022 Coleman Lantern 17B are 14" X 5-1/2" wheels with a 5 on 4-1/2 bolt pattern. The Karrier ST215/75R14 Radial Trailer Tire with 14" Galvanized Wheel - 5 on 4-1/2 - Load Range C, part…

view full answer...

Does Redarc In-Vehicle BCDC Battery Charger # 331-BCDC1240D Require Shore Power

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching