Replacement Mounting Bracket Recommendation for RV Steps

Question

Question:

Hi, I ordered a new set of steps but what is actually broken is the item that the stairs attach to but I do not know what it is called. It LJ a support box of some sort. Thanks

asked by: Gary T

0

Expert Reply:

Sounds like the outriggers are what you need to replace. For that we have the # LC301704 which we recommend when people are installing new trailer steps.

expert reply by: Jameson C

0

Answer 1

Outriggers such as #LC301704 bolt to the sides of steps such as #LC432698. The outriggers will bolt to the RV frame. For hardware to attach the steps to the outriggers use #LC118155-72. The specific location and orientation of the outriggers depends…

view full answer...

Answer 2

When changing the amount of steps you have on an RV like with the #SMFP-3100 it's pretty common that the widths of the brackets don't match up perfectly, but the good news is you can still install a different set as long as you are willing to…

view full answer...

Answer 3

We have an abundance of steps for you to choose from whether you prefer to replace the current steps on your Jayco Eagle or use free-standing steps such as the Econo Porch Trailer Step, #EHS-102-R-HR. However, RV steps are not specific to the make,…

view full answer...

Answer 4

The easiest way to determine if you have a first or second generation MORryde Stepabove 3-step setup is to look at the way the step legs lock and adjust. If they have a removable pin you have a first generation and need the part #MR93RR. If instead…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Replacement Mounting Bracket Recommendation for RV Steps

Products Referenced in This Question

Continue Researching