Thickness of Stallion Ramp 288-07489 When Laid Flat on Hard Surface

Question

Question:

What is the total thickness of the ramp when laying flat including arch. Want to verify storage options

asked by: Tyler R

0

Expert Reply:

I went to our warehouse and laid flat one of the Stallion ramps in the set # 288-07489. The tallest point in the arch is where the yellow safety sticker is placed and at this tallest point the height (or thickness, if you prefer) is 3-3/4-inches.

expert reply by: Adam R

0

Answer 1

The ramp set part #288-07489 that you referenced has a combined weight capacity of 3,000 lbs for both. Individually each has a 1,500 lb capacity and each ramp has three prongs that lean on the trailer. So each of them is rated for 500 lbs…

view full answer...

Answer 2

The 3000 lb capacity would mean that each ramp can handle a maximum of 1500 lbs applied to it or 3000 lbs for the pair. Since your tractor weighs 3500 lbs, I wouldn't use these ramps if the weight from both axles would be on the ramps at the…

view full answer...

Answer 3

We have various jack and stabilizer products that you can consider for addition to the rear of your equipment trailer to support it during loading processes. I linked our main page for such items so you can see all we offer. If you want a low-cost…

view full answer...

Answer 4

For your application I recommend installing the Square Drop Leg Stabilizer Jack #SJ-R208 which is a weld-on application that provides 18" of travel and a 2,000 lb weight capacity. To stabilize your trailer you basically need something to…

view full answer...

Answer 5

The outside dimensions of the outside tube of the #SJ-R208 measures 1-1/2 inch by 1-1/2 inch. The overall length is 8 inches. The outside dimensions of the inner leg are 1-1/4 by 1-1/4 inch. For more info and more dimensions check out the review…

view full answer...

Answer 6

The rungs on the Stallion Loading Ramp Set #288-07489 that you referenced have 3" gaps between them as you can see in the attached photo. My contact at Stallion confirmed this. If the spacing is too much for you to use and the 3,000 lbs…

view full answer...

Answer 7

Yep, you can use them; since the total capacity is 3,000 lbs - 1,500 lbs per ramp - a 2,000 lb vehicle is definitely light enough for the ramps. The ramps come in a pair, and measure (individually) 65" long and 20-1/2" wide: -…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Thickness of Stallion Ramp 288-07489 When Laid Flat on Hard Surface

Product Page this Question was Asked From

Continue Researching