Install Instructions for the Yakima Replacement Adapter Sleeve # Y8890342

Question

Question:

Are there any directions on how to install this part properly?

asked by: David L

0

Expert Reply:

I attached a picture that has the install instructions for the Replacement Adapter Sleeve # Y8890342 that you referenced that I got from Yakima.

expert reply by: Jameson C

0

click to enlarge

Answer 1

While there aren't specific written instructions for Replacement Adapter Sleeve #Y8890342 I can tell you how it goes on. You will just need to line up the pin holes and mounting holes on the adapter with the associated holes on the bike rack…

view full answer...

Answer 2

I have good news for you! This particular Yakima Replacement Sleeve #Y8890342 will work with your Yakima HighLite2. It was only the Yakima DoubleDown hanging racks that were made before 2014 that will not work with this adapter.

view full answer...

Answer 3

The correct replacement shank adapter for the Yakima TwoTimer 2 Bike Platform Rack is the Replacement Yakima Two Timer 2 Inch Adapter part #8880519.

view full answer...

Answer 4

I spoke with my contact at Yakima about your older model Yakima ROC bike rack. The #Y8890174, that you referenced, is designed to fit the Yakima FlipSide or StikUp bike racks only. For the older model Yakima ROC bike racks there is no longer an…

view full answer...

Answer 5

To find out if the Yakima Replacement Adapter Sleeve #Y8890342 is the correct part for your hitch bike rack you'll first want to try to confirm that the rack is either one of the HighLite or DoubleDown Ace racks. The hole in the rack's shank…

view full answer...

Answer 6

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 7

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 8

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 10

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 11

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Install Instructions for the Yakima Replacement Adapter Sleeve # Y8890342

Product Page this Question was Asked From

Continue Researching