How to Run the Wires Through the Firewall of a Ford Flex for a Brake Controller
Question:
how can u get the wire thru the firewall when there is no open space any where to run the darn thing for the electric brake.there is not an open spot under this hood for anything
asked by: Jodie
Expert Reply:
On your Ford Flex you will first want to remove the driver's side kick panel. Once the panel is exposed you will then need to look for a large rubber grommet which contains a bundle of wires that runs from the cab to the power distribution center (PDC) in the engine bay compartment. This grommet is usually located where the steering shaft goes through the firewall and connects to the rack and pinion. You can either remove the wire loom from the bundle of wires and then slide the 12 volt power wire for the brake controller though or you can just simply poke a hole in the grommet and run the wire though that way.
In order to install a brake controller like the Tekonsha Prodigy P3 Trailer Brake Controller part # 90195 on your Ford Flex you will need both a 4-way wiring harness and a 4 to 7-way adapter like part # ETBC7. If you can let me know what year Ford Flex you have I would be happy to offer the correct 4-way harness for you and provide you with an install video if available.
Products Referenced in This Question
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Product Page this Question was Asked From
Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LCD Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: How to Install Lights In a Enclosed Trailer And Upgrade the Breakaway Battery To Power The Lights
- Shop: Trailer Wiring
- Search Results: i26
- Shop: Brake Controller
- Shop: Vehicle Tow Bar Wiring
- Video: Roadmaster Universal Diode Wiring Kit Installation - 2021 Ford Ranger
- Shop: Roadmaster 4-Diode Universal Wiring Kit for Towed Vehicles - 7-Way to 6-Wire Hybrid Cord
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2018 Jeep Grand Cherokee C55774
- Video: Trailer Wiring Harness Installation - 2014 Ford Flex
- Video: Tekonsha Trailer Wiring Harness Installation - 2016 Ford Flex
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2019 Ford Flex
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 4-Pole Flat Trailer Connector
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 7-Way and 4-Pole Flat Connectors
- Video: etrailer SD Non-Binding Tow Bar Installation - 2015 Chevrolet Sonic
- Video: Roadmaster Tow Bar Wiring Kit Installation - 2017 Ford Expedition
- Q&A: Battery Disconnect for Flat Towing 2016 Ford Focus
- Q&A: Why Does the Battery Need to be Disconnected to Flat Tow a Ford Edge
- Q&A: Why Disconnect Battery to Flat Tow Vehicle Behind Motorhome
- Shop: Trailer Hitch
- Shop: Base Plate for Tow Bar
- Q&A: Which Pin On A 7-Way Should Have Constant 12V Power When Vehicle Is Running
- Q&A: Installing Brake Controller And Wiring Harness On 2015 Ford Flex Without Factory Tow Package
- Q&A: Recommended Supplemental Braking System Recommendation for Land Rover Discovery II
- Shop: Vehicle Tow Bar Brake System
- Search Results: roadmaster braking
- Search Results: patriot 3
on Trailer Brake Controller
