Vent Assembly Replacement For Holiday Rambler Aluma Lite

Question

Question:

I have a 1986 Holiday Rambler Aluma lite. On the Vent it has the part number AS-13-M-V101. Id like to replace the entire assembly. Which one would be the best fit.

asked by: Dusty C

0

Expert Reply:

Since your 1986 Holiday Rambler Alumalite has the Replacement Dome Assembly for Ventline Ventadome # BVD0449-A01 on it, that means that the following Trailer Roof Vents will fit:

The Ventline Ventadome Trailer Roof Vent # V2092SP-28 has a manual lift and does not have a fan.

The Ventline Ventadome Trailer Roof Vent # V2094SP-28 has a manual lift and a 12V fan.

The Ventline Ventadome Roof Vent # V2119-601-00 has a powered lift and a 12V Fan.

The Ventline Roof Vent # V2128SP-01 has a manual lift and a 110V fan.

Screws and sealer are not included. Installation Kit # 344270KITW includes all necessary screws and sealer to install vent.

All of these vents will fit inside a opening of 14-1/4" wide x 14-1/4" long so it all comes down to personal preference and what your trailer is equipped with.

expert reply by: Timothy G

0

Answer 1

There is not a cross-reference to specify the exact vent lid that you need. I can tell you that there are not any 13" X 13" vents. Your dad probably measured the inside narrowest part of the vent. Universally the vent openings on the roof…

view full answer...

Answer 2

We do have most of the parts that you referenced and although we don't have instructions we do have some diagrams on each of the product pages that you can check out. Item 7 - #VC0476-00 Item 14 - #BV0115-04 We don't have items 1, 15 and, 16,…

view full answer...

Answer 3

There are replacement covers that are smoke colored for your Ventline Roof Vent, #V2128SP-01. The part you are looking for is Replacement Dome Assembly for Ventline - Smoke, #BVD0449-A03.

view full answer...

Answer 4

The Ventline Roof Vent w/ 110V Fan #V2128SP-01 that your referenced requires the standard rough cut opening right at 14-1/4 inch square. This is the only option that uses 110 volt power as well. I attached a review video for more info as well.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Vent Assembly Replacement For Holiday Rambler Aluma Lite

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching