Is There a Height to Install Horse Trailer Breast Pad

Question

Question:

I am wondering what the average suggested installation height is.

asked by: Cassandra

0

Expert Reply:

There is not a recommended height to install the Horse Trailer Breast Pad # HTP24BK; you can install them where you think they will be most effective. To install these in your trailer we have Trailer Horse Pad Screw # PS-8 which is a 3/4" #8 screw.

expert reply by: Kyle S

0

click to enlarge

Answer 1

A 3/8" self tapping screw seems a bit large for the Horse Trailer Side Pads #HTP1260BK but I do recommend always using a washer like the 3/8" #01292006-020-01. This will help spread out the surface area which means the pad is less…

view full answer...

Answer 2

There is not a specific method for attaching the Horse Trailer Side Pad, #HTP60BK, to the trailer wall. You can use the Trailer Horse Pad Screw, #PS-8, but like you said it will puncture the material. Another option you have is to apply adhesive to…

view full answer...

Answer 3

When replacing your horse trailer pads, be sure to pad all dividers and walls. The pads are constructed of a very durable vinyl sewn over 2" of foam onto rigid cardboard. They stand the test of time and hold up in all climates. There is no…

view full answer...

Answer 4

Are the holes you are referring to threaded? If so then you could drill a 1/4" hole into one of our pads (see below) and then use a bolt to attach them to the wall. If the holes are not threaded then it may just be best to use a few phillips…

view full answer...

Answer 5

Yes. You will have to use the Demco Hijacker Autoslide Capture Plates for Trailair Rota-Flex Pin Boxes #DM6171 on your 2021 Grand Design Reflection 337RLS. As far as which Curt Flexair works for your trailer, it depends on what pinbox you currently…

view full answer...

Answer 6

Yes, you can charge the 12V battery on your Bright Way Trailer Breakaway Kit with 0.5-Amp Charger and 5 Ah Battery #3802339 while in storage. If you don't already have a charger you can use the CTEK MULTI US 7002 12-Volt Universal Battery Charger…

view full answer...

Answer 7

To charge the battery in the Engager Trailer BreakAway Kit, #20099, you can attach the wire from the 12 volt circuit on the trailer side 7-Way (1 oclock position on the back of the trailer side 7-Way where the wires attach) to the input wire on the…

view full answer...

Answer 8

They are different in width. Aside from that and price everything else is the same. The Horse Trailer Side Pad item #HTP1260BK measures 60" long x 12" wide x 2" thick. The Horse Trailer Side Pad item #HTP60BK measures 60" long x…

view full answer...

Answer 9

Horse trailer pad #HTP24BK does not come pre-drilled because then it would limit what and where it could fit. We also recommend trailer horse pad screw #PS-8 to mount the pad. The screws are sold in quantities of 1.

view full answer...

Answer 10

We don't offer replacement horse trailer side pads in custom sizes, but for a larger size than the part #HTP40BK you would want the part #HTP60BK as this one is 60 inches long instead of 40 inches like the #HTP40BK.

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hi Kat, The rubber bumpers that we offer are all 96" in length but can come in different widths. Based on the dimensions you provided i your pictures the #D3-96 is going to be the best fit, but you will have to cut it down to size.

view full answer...

Is There a Height to Install Horse Trailer Breast Pad

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching