Diameter of Hole Necessary for Valterra # A10-3358VP

Question

Question:

Very good video but what size hole needs to be in the ceiling? One more important measurement please.

asked by: Gary R

0

Expert Reply:

The diameter of the hole in the ceiling for the Valterra A/c Ceiling Register # A10-3358VP is 5-13/16". You'll also need a depth of right at 7/8" to accommodate the vent.

expert reply by: Jason S

0

Answer 1

The Greystone Built-in Microwave with Trim Kit part #324-000105 is the best replacement option for an Apollo Microwave AAC24BIB in regards to size. The Greystone Built-in Microwave measures 23-3/8" wide x 15" tall with the trim kit…

view full answer...

Answer 2

Yes, the Lippert Components Power Stabilizer Jack #LC298707 that you referenced is what you will want to replace your jack with the part number 369777 (as pictured) with. My contact at Lippert Components verified this.

view full answer...

Answer 3

The light beige Valterra Adjustable A/C Ceiling Register part #A10-3360VP has more of a pale brown tone to it then the Valterra Adjustable A/C Ceiling Register medium white part #A10-3359VP. If you would like more of a light brown color, I recommend…

view full answer...

Answer 4

If the register you're replacing is more of an off-white/cream then you will want to go with the Valterra A/C Ceiling Register - White #A10-3358VP. This is an off-white color compared to the brighter, pure white on the Valterra Medium White…

view full answer...

Answer 5

For standard pin boxes you do not need to use a locking plate with the Demco Hijacker hitch #DM8550034 but if you use the following cushioned pin boxes: Glide Ride, Mor Ryde, Trailair Tri Glide, Trailair Flexair, Rota Flex, and 5th Airborne you would…

view full answer...

Answer 6

I have a solution for you but there isn't just a replacement converter section for the Elixir ELX-45. You're going to need to replace the entire panel with the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger item…

view full answer...

Answer 7

The Replacement Air Distribution Box w/ LEDs for Furrion Chill RV Air Conditioner #FACT12LA-PS was designed to replace the older style that you sent in a picture of and would work great. It has the LEDs like you are wanting as well.

view full answer...

Answer 8

There's not many differences between the Air Lift WirelessONE item #AL25980EZ and item #AL25980. The main difference is that the item #AL25980EZ has a slightly higher CFM at 1.03 compared to 0.92 and it runs slightly more efficient at 9% over 15%…

view full answer...

Answer 9

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 10

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 11

The gauge used with the heavy duty Air Lift compressor system, #AL25854, has 4 wires because the switch is built into the gauge. The black wire is the ground, white is the signal to the compressor, red and green are ignition power wires. I have…

view full answer...

Answer 12

The Grease Seal part #168233 has a double lip so it can be used on a boat trailer and be submersed under water, yes. This is also the correct replacement for the NOK AD2527E Grease Seal that you have now.

view full answer...